Fertan FeDOGEL 750 ml Rust-Remover-Gel One of the most trusted product by industries and classic car enthusiast for rust treatments for over 38 years. FERTAN products have been bestselling rust removers, coatings and primers in Germany and several other European countries for several years now. FERTAN® RUST REMOVER GEL is perfect for the removal of rust and corrosion on metal parts, especially in hard to reach places. The gel can easily be applied using a brush or sponge and has a relatively short reaction time when compared to liquid solutions. RECOMMENDED FOR: Rust-proofing and maintenance inter-ventions on any material that rusts.   Features: Can be applied directly with brush or sponge for hard-to-reach areas Water-based, non-toxic & biodegradable Completely removes rust, does not mask it Content (metric): 750 ml Item no.: 23530   Anwendung: Der Gel-Film in ca. 3-5 mm Stärke aufgetragen löst die Korrosion. Vor Gebrauch alle Sicherheitshinweise lesen und verstehen. Schutzkleidung, Augenschutz/Gesichtsschutz und Schutzhandschuhe tragen. Auftrag mit Pinsel oder Schwamm Reaktionszeit 10-60 Minuten. Vor Austrocknung schützen. Rückstandslos mit Wasser, ggfs. mit Bürste oder Schwamm reinigen. Bei sehr starker Korrosion Vorgang wenn notwendig wiederholen. Originalgebinde dicht verschlossen halten und vor direktem Sonnenlicht geschützt bei 5°C bic 25°C lagern. Anbruchgebinde kurzfristig verarbeiten. Gereinigte Teile möglichst schnell mit geeignetem Rostschutz vor erneuter Korrosion schützen. Z.B. mit MM30, FERPOX Epoxy Primer, Farbe, Wachs etc.   Gefahrenhinweise: Einstufung gemäß Verordnung (EG) Nr. 1907/2006 Verursacht schwere Augenreizung. Gesundheitsschädlich bei Einatmen Sicherheitshinweise Ist ärztlicher Rat erforderlich, Verpackung oder Kennzeichnungsetikett bereithalten. Darf nicht in die Hände von Kindern gelangen. Aerosol/Sprühnebel nicht einatmen. Gummihandschuhe., Dicht schließende Schutzbrille. tragen. BEI EINATMEN: Die Person an die frische Luft bringen und für ungehinderte Atmung sorgen. BEI KONTAKT MIT DEN AUGEN: Einige Minuten lang behutsam mit Wasser spülen. Vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülen. Bei anhaltender Augenreizung: Ärztlichen Rat einholen/ärztliche Hilfe hinzuziehen.

  Fertan Rust Converter, 1 Liter   The FERTAN rust converter is the perfect rust converter. With the FERTAN rust converter you can easily remove strong rust. For optimal rust removal.   Features: 1 litre standard dose for the removal of rust and corrosion of carbon steel for vehicles, vehicle parts and fuel tanks, car body cavities for metal constructions, ships, ship parts, port facilities for steel halls, conservatories and other carbon steel components Proven for decades in restoration the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallically clean, but not rust-free   Fertan Rust converter advantages: As a rust converter, FERTAN dissolves the existing rust layer (Fe3) and decomposes it into a non-reactive powder. The non-corrosive Fe2 layer underneath is protected with the new metal bond and the previously corroded metal can be provided with the required final protection within 6 months. This can be used in paint, varnish, wax, tar, zinc, epoxy resin, etc. e. be. FERTAN rust converter can be used successfully on slightly rusted, strong rust and also on bare metal. The protective effect is achieved in principle. The product is also water-based for environmental reasons. For this reason, the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallic clean, but not rust-free. Only with extremely strong rust layers, over 5 mm, a second treatment may be necessary. However, use FERTAN only at temperatures above 5°C and leave on for about 24 – 48 hours. Always clean the surface with water before the final treatment. The FERTAN rust converter can be used even on damp surfaces and is free of pollutants.   Application: FERTAN Rust converter Application: (Shake before use) Remove loose rust and prepare a smooth lacquerable surface for the surface to be painted later. (e. g. by grinding) Before applying FERTAN, it is important to clean surfaces of oil, grease, silicone and dirt. Apply FERTAN using a clean brush, roller or spray gun.   Temperature information: Allow FERTAN to act at temperatures above 20°C for 24 hours. In dry environment or direct sunlight, moisten slightly after 1-2 hours (fog moisture). At temperatures of 5 – 19° C, extend the reaction time to approx. 48 hours, or longer. Do not use in frost and temperatures below 5° C!   Surface turns black – blue violet Ideal for post-treatment after 6 months at the latest: Filler, primer (FERPOX, MM30), colour, cavity protection wash and underbody protection waxes (UBS 240), EP resins etc. Only rinse the surface with water before further treatment (the surface should not be damaged mechanically, otherwise the protective layer will be destroyed – no grinding, etc. ) This black, blue-violet surface can be overpainted with all conventional primers and varnishes, 1 litre of FERTAN is sufficient for approx. 12 – 15m2 surface when applied with a brush. FERTAN may cause stains on bright surfaces and absorbent surfaces, so cover them and wash splashes immediately with water, avoiding any open-pored material (e. g. wood, concrete, etc. ) that should not be processed. Clean tools after use with clear water. Wear protective clothing and follow safety instructions.    

Fertan Brake-Kit FeDOGEL + MM30 + Brush + Sponge for quick de-rusting of braking systems   Features: Product assembly for quick de-rusting of brake discs, brake drums and calipers: FEDOGEL for de-rusting MM30 Multi Metal coating Brush Sponge Contents sufficent for 1 vehicle or 4 brake systems Quick and perfect de-rusting Low workload No removal of the brakes necessary Extreme corrosion protection Extreme temperature resistance   Fertan FeDOGEL 500 ml Rust-Remover-Gel: FERTAN® RUST REMOVER GEL is perfect for the removal of rust and corrosion on metal parts, especially in hard to reach places. The gel can easily be applied using a brush or sponge and has a relatively short reaction time when compared to liquid solutions. RECOMMENDED FOR: Rust-proofing and maintenance inter-ventions on any material that rusts. Water-based, non-toxic & biodegradable Completely removes rust, does not mask it Content (metric): 500 ml   Fertan MM30 Multi Metal Coating 400 ml Spray: Multi-metal coating with aluminum-titanium-zinc cathodic long-term corrosion protection. Extremely resistant and very high-quality surface quality after full hardening. Very good adhesion to steel, aluminum, and copper, can be overpainted as a bonding bridge with commercially available 1-component and 2-component paints. Spot weldable. Resistance over 500 hours at only 15 μm in salt spray test. Use on car bodies, steel frames, steel construction, heating and ventilation construction and industry.