Fertan HT Cavity Protection Wax, 500 ml   FERTAN cavity protection wax was developed for the preservation of car cavities based on wax.   Features: 500 millilitres spray can for the end protection of cavities, e. g. in car bodies The composition of the product allows easy processing without the product flowing out of the cavities. Due to the presence of resins, an optimal adhesion is achieved, even on vertical surfaces, etc. HT wax remains very soft and thus obtains the property of automatically closing small cracks in the coating even after years. for many years successful: in the restoration of vintage cars in the restoration of new motor vehicles Coating of industrial structures   Processing: Shake well before use. FERTAN cavity protection Insert wax into the cavities by means of a cavity gun with 360° nozzle. Use the boreholes installed by the vehicle manufacturer or, if necessary, install new boreholes. Apply wax to the edges of the holes. FERTAN cavity protection Wax does not drip. Remove any splashes with test petrol. Processing temperature: The optimum processing temperature and the temperature of the body should be min. 20°C. For restorations and post-treatment: Apply wax 24 hours after rust removal by FERTAN rust converters. Please note the processing instructions for the rust converter. After rust removal and before application of cavity protective wax, pre-treat the welds and sheet metal overlaps with a layer of PREWAX pre-treatment wax, a seam-penetrating protective wax with extreme creepability. Then apply cavity protection wax in several thin layers, staggered by 12-48 hours to compensate for shrinkage cracks. Dry season: At + 20° C: approx. 5 hours Consumption: approx. 6 - 10 spray cans litres for a medium class passenger car Processing pressure: cavity suction cup gun with 360° nozzle approx. 6 – 9 bar cavity pressure cup gun with 360° nozzle approx. 3 – 4. 5 bar  

Fertan Underbody protection wax, 1 Liter Features: Fertan UBS 240 is an underbody protection wax for long-term protection PVC-compatible, in a transparent to slightly amber color. The "amber effect" is reinforced, the more of the product is being applied. Fertan UBS 240 is an ideal protective wax-based product, especially for underbodies of motor vehicles Can be used even in extreme conditions to protect over long term. Fertan can also be applied to lacquered underbodies. Highly flammable Irritant Environmental damaging

Fertan HT Cavity Protection Wax, 5 Litre   FERTAN cavity protection wax was developed for the preservation of car cavities based on wax.   Features: 5 litre canister for the end protection of cavities, e. g. in car bodies The composition of the product allows easy processing without the product flowing out of the cavities. Due to the presence of resins, an optimal adhesion is achieved, even on vertical surfaces, etc. HT wax remains very soft and thus obtains the property of automatically closing small cracks in the coating even after years. for many years successful: in the restoration of vintage cars in the restoration of new motor vehicles Coating of industrial structures   Processing: Shake well before use. FERTAN cavity protection Insert wax into the cavities by means of a cavity gun with 360° nozzle. Use the boreholes installed by the vehicle manufacturer or, if necessary, install new boreholes. Apply wax to the edges of the holes. FERTAN cavity protection Wax does not drip. Remove any splashes with test petrol. Processing temperature: The optimum processing temperature and the temperature of the body should be min. 20°C. For restorations and post-treatment: Apply wax 24 hours after rust removal by FERTAN rust converters. Please note the processing instructions for the rust converter. After rust removal and before application of cavity protective wax, pre-treat the welds and sheet metal overlaps with a layer of PREWAX pre-treatment wax, a seam-penetrating protective wax with extreme creepability. Then apply cavity protection wax in several thin layers, staggered by 12-48 hours to compensate for shrinkage cracks. Dry season: At + 20° C: approx. 5 hours Consumption: approx. 5 litres canister for a medium class passenger car Processing pressure: cavity suction cup gun with 360° nozzle approx. 6 – 9 bar cavity pressure cup gun with 360° nozzle approx. 3 – 4. 5 bar  

  Fertan Rust Converter, 250 ml   The FERTAN rust converter is the perfect rust converter. With the FERTAN rust converter you can easily remove strong rust. For optimal rust removal.   Features: 250 millilitre spray gun for the removal of rust and corrosion of carbon steel for vehicles, vehicle parts and fuel tanks, car body cavities for metal constructions, ships, ship parts, port facilities for steel halls, conservatories and other carbon steel components Proven for decades in restoration the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallically clean, but not rust-free   Fertan Rust converter advantages: As a rust converter, FERTAN dissolves the existing rust layer (Fe3) and decomposes it into a non-reactive powder. The non-corrosive Fe2 layer underneath is protected with the new metal bond and the previously corroded metal can be provided with the required final protection within 6 months. This can be used in paint, varnish, wax, tar, zinc, epoxy resin, etc. e. be. FERTAN rust converter can be used successfully on slightly rusted, strong rust and also on bare metal. The protective effect is achieved in principle. The product is also water-based for environmental reasons. For this reason, the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallic clean, but not rust-free. Only with extremely strong rust layers, over 5 mm, a second treatment may be necessary. However, use FERTAN only at temperatures above 5°C and leave on for about 24 – 48 hours. Always clean the surface with water before the final treatment. The FERTAN rust converter can be used even on damp surfaces and is free of pollutants.   Application: FERTAN Rust converter Application: (Shake before use) Remove loose rust and prepare a smooth lacquerable surface for the surface to be painted later. (e. g. by grinding) Before applying FERTAN, it is important to clean surfaces of oil, grease, silicone and dirt. Apply FERTAN using a clean brush, roller or spray gun.   Temperature information: Allow FERTAN to act at temperatures above 20°C for 24 hours. In dry environment or direct sunlight, moisten slightly after 1-2 hours (fog moisture). At temperatures of 5 – 19° C, extend the reaction time to approx. 48 hours, or longer. Do not use in frost and temperatures below 5° C!   Surface turns black – blue violet Ideal for post-treatment after 6 months at the latest: Filler, primer (FERPOX, MM30), colour, cavity protection wash and underbody protection waxes (UBS 240), EP resins etc. Only rinse the surface with water before further treatment (the surface should not be damaged mechanically, otherwise the protective layer will be destroyed – no grinding, etc. ) This black, blue-violet surface can be overpainted with all conventional primers and varnishes, 1 litre of FERTAN is sufficient for approx. 12 – 15m2 surface when applied with a brush. FERTAN may cause stains on bright surfaces and absorbent surfaces, so cover them and wash splashes immediately with water, avoiding any open-pored material (e. g. wood, concrete, etc. ) that should not be processed. Clean tools after use with clear water. Wear protective clothing and follow safety instructions.    

  Fertan Rust Converter, 1 Liter   The FERTAN rust converter is the perfect rust converter. With the FERTAN rust converter you can easily remove strong rust. For optimal rust removal.   Features: 1 litre standard dose for the removal of rust and corrosion of carbon steel for vehicles, vehicle parts and fuel tanks, car body cavities for metal constructions, ships, ship parts, port facilities for steel halls, conservatories and other carbon steel components Proven for decades in restoration the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallically clean, but not rust-free   Fertan Rust converter advantages: As a rust converter, FERTAN dissolves the existing rust layer (Fe3) and decomposes it into a non-reactive powder. The non-corrosive Fe2 layer underneath is protected with the new metal bond and the previously corroded metal can be provided with the required final protection within 6 months. This can be used in paint, varnish, wax, tar, zinc, epoxy resin, etc. e. be. FERTAN rust converter can be used successfully on slightly rusted, strong rust and also on bare metal. The protective effect is achieved in principle. The product is also water-based for environmental reasons. For this reason, the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallic clean, but not rust-free. Only with extremely strong rust layers, over 5 mm, a second treatment may be necessary. However, use FERTAN only at temperatures above 5°C and leave on for about 24 – 48 hours. Always clean the surface with water before the final treatment. The FERTAN rust converter can be used even on damp surfaces and is free of pollutants.   Application: FERTAN Rust converter Application: (Shake before use) Remove loose rust and prepare a smooth lacquerable surface for the surface to be painted later. (e. g. by grinding) Before applying FERTAN, it is important to clean surfaces of oil, grease, silicone and dirt. Apply FERTAN using a clean brush, roller or spray gun.   Temperature information: Allow FERTAN to act at temperatures above 20°C for 24 hours. In dry environment or direct sunlight, moisten slightly after 1-2 hours (fog moisture). At temperatures of 5 – 19° C, extend the reaction time to approx. 48 hours, or longer. Do not use in frost and temperatures below 5° C!   Surface turns black – blue violet Ideal for post-treatment after 6 months at the latest: Filler, primer (FERPOX, MM30), colour, cavity protection wash and underbody protection waxes (UBS 240), EP resins etc. Only rinse the surface with water before further treatment (the surface should not be damaged mechanically, otherwise the protective layer will be destroyed – no grinding, etc. ) This black, blue-violet surface can be overpainted with all conventional primers and varnishes, 1 litre of FERTAN is sufficient for approx. 12 – 15m2 surface when applied with a brush. FERTAN may cause stains on bright surfaces and absorbent surfaces, so cover them and wash splashes immediately with water, avoiding any open-pored material (e. g. wood, concrete, etc. ) that should not be processed. Clean tools after use with clear water. Wear protective clothing and follow safety instructions.    

Fertan HT Cavity Protection Wax, 1 Litre   FERTAN cavity protection wax was developed for the preservation of car cavities based on wax.   Features: 1 litre normdose for the end protection of cavities, e. g. in car bodies The composition of the product allows easy processing without the product flowing out of the cavities. Due to the presence of resins, an optimal adhesion is achieved, even on vertical surfaces, etc. HT wax remains very soft and thus obtains the property of automatically closing small cracks in the coating even after years. for many years successful: in the restoration of vintage cars in the restoration of new motor vehicles Coating of industrial structures   Processing: Shake well before use. FERTAN cavity protection Insert wax into the cavities by means of a cavity gun with 360° nozzle. Use the boreholes installed by the vehicle manufacturer or, if necessary, install new boreholes. Apply wax to the edges of the holes. FERTAN cavity protection Wax does not drip. Remove any splashes with test petrol. Processing temperature: The optimum processing temperature and the temperature of the body should be min. 20°C. For restorations and post-treatment: Apply wax 24 hours after rust removal by FERTAN rust converters. Please note the processing instructions for the rust converter. After rust removal and before application of cavity protective wax, pre-treat the welds and sheet metal overlaps with a layer of PREWAX pre-treatment wax, a seam-penetrating protective wax with extreme creepability. Then apply cavity protection wax in several thin layers, staggered by 12-48 hours to compensate for shrinkage cracks. Dry season: At + 20° C: approx. 5 hours Consumption: approx. 5 litres canister for a medium class passenger car Processing pressure: cavity suction cup gun with 360° nozzle approx. 6 – 9 bar cavity pressure cup gun with 360° nozzle approx. 3 – 4. 5 bar  

Fertan Body protection, black, 1 l   FERTAN bodywork and stone guard form an elastic layer with a fine-grained structure, which provides a resistant protection against stones, road debris and water. 1 liter standard can Fast drying Overpaintable Colour: black Anti drone effect   Features: FERTAN body and stone guard protects against petrol, oil, water and salt. In addition, the product has excellent damping and sound absorbing properties. The product is made of synthetic resin and contains no bitumen or tar constituents. It can be over-painted with all common acrylic paints. Particularly good adhesion to steel, stainless steel, galvanized steel, aluminium  and polyester laminates. The 1 litre containers have a standard 38mm thread for connection to a underbody gun.   Application: Preparation of the substrate for optimal adhesion: Shake well before use. Before applying, clean and degrease the surface, eg FERTAN Silcone Remover. Cover areas and parts that are not to be coated. eg brakes, exhaust, catalytic converter, ect.   Pretreat surfaces: Steel: degrease and if necessary grind. Galvanized sheets and Aluminium: matt with abrasive wool and degrease. Stainless steel: degrease. Polyester laminates: degrease, sand with sandpaper P80 - P120 and degrease again. When applied directly to steel, a primer is recommended. Processing pressure and nozzle Apply with spray gun, nozzle approx. 4 mm and 2-4 bar working pressure. Lower pressure for an increased structure on the surface.   Overpainting: 60 minutes after application at approx. 20 ° C at the earliest.   Theoretical consumption: 1 liter at 100 μm thickness sufficient for approx. 3-4 m² area.   Storage: Store in dry and cool room, avoid direct sunlight. Protect from ignition and heat sources. Can be stored at 20 ° C for approx. 2 years in the original unopened container.  

Fertan UBS 240 Unterbody protection wax 5 L   Features: 5000 ml PVC - compatible: contains no aromatic ingredients wax-based: best adhesion work even in thick or thin layers contains special additives: highly friction-resistant-water-repellent transparent-amber: useful at all unterbody and chassis parts highly-abrasion resistant: strong mechanical capacity highest resistance in the environment: more than 1000 hrs. salt fog test resistance   Usage: Because of its special viscosity UBS 240 may be applied by means of an airless spray gun or by commonly-available proprietary guns. Even at a temperatures of over 30 deg C the product doesn’t drip. The ideal application temperature is around 20 deg. C. If the product is to be applied by means of a paintbrush, it is recommended to heat the can in a tub of warm water. Do not heat in an oven or other form of heating equipment. Applied in thin layers on painted surfaces, e.g painted underbodies, UBS 240 offers best protection. In the presence of corrosion use FERTAN rust converter first. Very useful after Fertan stone chip protection in thin film   Technical features: The product forms even in thin layers a perfect protection film which gives at painted or galvanized surfaces best possible appearance. On unprotected underbodies a first layer with resin-based Fertan stone-chip, is recommended. At overlaps or welded joints a first protection with PREWAX should be used. At low temperatures the product should be heated up to 25 deg C. in a tub of warm water. Do not heat on an oven or any other form of heating equipment please. In the way the creeping characteristic will be improved.

Fertan Underbody Protection Wax, 500 ml, Spray Can Features: UBS 220 is an underbody protection wax PVC compatible, in a transparent to slightly amber color The "amber effect" is being reinforced the more of the product is applied. Thus UBS 220 is an ideal protective, wax-based product. It can be used for long term protection for underbodies of motor vehicles or with lacquered floors - even in extreme conditions! Irritant Highly flammable Environmental damaging