Kukko Set of two- and three-arm pullers with narrow jaws K-2030-20-S   Description 7 in 1 kit in the tried-and-tested KUKKO-L-Boxx system. The set facilitates the assembly of seven pulling device models through the combination of pulling jaws and extensions. Flexibility assured thanks to two-arm or three-arm design. Narrow pulling jaws. Jaw extensions. Parallel pulling hooks in every position, even with full load. Pulling hooks with infinitely variable adjustment on the cross-beam. Optimal adjustment of the spindle to the shaft with 2-sided spindle tip (ball and tip). Short and long mechanical pressure screws. Milled thread treated with special coating. Includes a pressure pad set for supporting the pressure spindle in a hollow shaft. If there is adequate free space around the part to be removed, we recommend using a 3-jaw puller. Instructions on the cover. Secure storage in special foam. Personal KUKKO-Chip-Code. Use For removing large bearings, gears, discs, etc. for tight or difficult-to-access spaces. Advantage Practical package for universal use. The thin pulling hooks are suitable for narrow, difficult-to-access locations. Variable reach thanks to optional jaw extensions. Can be installed on various pulling hooks. Turning the pulling hooks enables them to be used both internally and externally. Suitable for pulling asymmetric workpieces. 2-arm cross bar with hexagonal profile for good grip. Spindle head band prevents the wrench from slipping off. Almost all components available as replacement parts, time-saving order process thanks to numbering system. Complete easy-to-manage package. KUKKO-L-Boxx-System compatible with systems by all common manufacturers. How it works The part due to be removed (e.g. a gear, pulley or ball bearing) is gripped from the outside. Tightening of the pressure screw and the resulting pressure removes the part from the shaft. The puller must be positioned centrally for centre shafts. If the shaft is not sitting centrally, the parts can be removed asymmetrically with pullers with parallel pulling hooks. Safety information The pulling hooks´ sliding parts must always sit stably and fully on the cross-beam. If several parts have to be removed, always follow a step-by-step process. Do not remove several parts at the same time. The pulling hooks´ support surfaces must always be straight and sit fully beneath the part to be removed. Do not use any electrical or pneumatic servo screwdrivers or hammer drills. Protective blanket required. Protective goggles required. Item no. EAN 4021176 Clamping reach outside mm Clamping reach outside inch Clamping depth mm Clamping depth inch Clamping reach inside mm Clamping reach inside inch Hex drive size mm Max. tonne t Weight kg K-2030-20-S 123276 150 - 600 5 7/8 - 23 5/8 200 7 7/8 100 - 260 3 7/8 - 10 1/4 24 5 14.5

Kukko Universal 2-jaw puller in set series 20-P   For removing bearings, gears, discs, etc.   Description Standard pulling hooks in various lengths. Parallel pulling hooks in every position, even with full load. Pulling hooks with infinitely variable adjustment on the cross-beam. Optimal adjustment of the spindle to the shaft with 2-sided spindle tip (ball and tip). Mechanical pressure screw. Milled thread treated with special coating. Two-arm design for space-saving operation.   Advantage Variable reach thanks to optional jaw extensions. Can be installed on various pulling hooks. Turning the pulling hooks enables them to be used both internally and externally. Suitable for pulling asymmetric workpieces. Spindle head band prevents the wrench from slipping off. Cross-beam with hexagonal profile for good grip. Almost all components available as replacement parts, time-saving order process thanks to numbering system. Note: Pressure pads from series 600-17 are a good addition if the shaft is hollow and the spindle cannot be supported. Stability support from optional series 219 clamp.   Series 20-P Item no. EAN 4021176 Clamping reach outside mm Clamping reach outside inch Clamping depth mm Clamping depth inch Clamping reach inside mm Clamping reach inside inch Hex drive size mm Max. tonne t Weight kg 20-10-P3 267611 120 4 3/4 100/200/250/350 3 7/8; 7 7/8; 9 7/8; 13 3/4 70 - 180 2 3/4 - 7 1/8 17 4,5 3.97 20-20-P2 003004 200 7 7/8 150/300 5 7/8; 11 7/8 100 - 260 3 7/8 - 10 1/4 17 6 5.905 20-30-P3 003011 350 13 3/4 200/300/400 7 7/8; 11 7/8; 15 3/4 180 - 440 7 1/8 - 17 3/8 19 8,5 17.1