Fertan Rust Converter, 1 Liter   The FERTAN rust converter is the perfect rust converter. With the FERTAN rust converter you can easily remove strong rust. For optimal rust removal.   Features: 1 litre standard dose for the removal of rust and corrosion of carbon steel for vehicles, vehicle parts and fuel tanks, car body cavities for metal constructions, ships, ship parts, port facilities for steel halls, conservatories and other carbon steel components Proven for decades in restoration the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallically clean, but not rust-free   Fertan Rust converter advantages: As a rust converter, FERTAN dissolves the existing rust layer (Fe3) and decomposes it into a non-reactive powder. The non-corrosive Fe2 layer underneath is protected with the new metal bond and the previously corroded metal can be provided with the required final protection within 6 months. This can be used in paint, varnish, wax, tar, zinc, epoxy resin, etc. e. be. FERTAN rust converter can be used successfully on slightly rusted, strong rust and also on bare metal. The protective effect is achieved in principle. The product is also water-based for environmental reasons. For this reason, the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallic clean, but not rust-free. Only with extremely strong rust layers, over 5 mm, a second treatment may be necessary. However, use FERTAN only at temperatures above 5°C and leave on for about 24 – 48 hours. Always clean the surface with water before the final treatment. The FERTAN rust converter can be used even on damp surfaces and is free of pollutants.   Application: FERTAN Rust converter Application: (Shake before use) Remove loose rust and prepare a smooth lacquerable surface for the surface to be painted later. (e. g. by grinding) Before applying FERTAN, it is important to clean surfaces of oil, grease, silicone and dirt. Apply FERTAN using a clean brush, roller or spray gun.   Temperature information: Allow FERTAN to act at temperatures above 20°C for 24 hours. In dry environment or direct sunlight, moisten slightly after 1-2 hours (fog moisture). At temperatures of 5 – 19° C, extend the reaction time to approx. 48 hours, or longer. Do not use in frost and temperatures below 5° C!   Surface turns black – blue violet Ideal for post-treatment after 6 months at the latest: Filler, primer (FERPOX, MM30), colour, cavity protection wash and underbody protection waxes (UBS 240), EP resins etc. Only rinse the surface with water before further treatment (the surface should not be damaged mechanically, otherwise the protective layer will be destroyed – no grinding, etc. ) This black, blue-violet surface can be overpainted with all conventional primers and varnishes, 1 litre of FERTAN is sufficient for approx. 12 – 15m2 surface when applied with a brush. FERTAN may cause stains on bright surfaces and absorbent surfaces, so cover them and wash splashes immediately with water, avoiding any open-pored material (e. g. wood, concrete, etc. ) that should not be processed. Clean tools after use with clear water. Wear protective clothing and follow safety instructions.    

Fertan Ferpox Epoxyprimer 800 ml can   Features: FERPOX is a 1-K epoxy primer Lead and chromate free temperature resistant from -40° C to + 250° C overcoatable FERPOX is applied like normal adhesive ground or primer particularly good adhesion to: Iron and steel Pre-treated aluminium hot-dip galvanized metal the ideal primer for all metals exposed to high stress or corrosion hazards: particularly high strength closed surface FERPOX can be injected (diluted) and coated Colour grey RAL 7012 800 ml container   Scope of application: Vehicle restoration: Subfloors Wheel arches Spray walls Frame and disc frames Battery holders etc.   Processing: FERPOX is applied like normal adhesive base or paint. Application is carried out by means of a brush, roller or spray gun. When applied with compressed air spray guns with max. Dilute 10% nitro dilution. When applying with a brush or roll, do not apply too high layer thicknesses, 1x thin layer is completely sufficient. Compressed air processing: Nozzle: 1. 5 Pressure: 2 – 4 bar Dilution: Nitro dilution (only) Theoretical yield: Different depending on the type of surface and processing. Yield: Film thickness Wet Dry Area 77μm 50 μm 6. 9 m2/kg 108 μm 70 μm 4. 8 m2/kg Technical data:   Delivery viscosity: approx. 150 sec. DIN 4 mm Density: approx. 1. 18 – 1. 24 kg/litre Overpaintable with 1-K and 2-K standard coatings: with 2-K max. 150 μm. Temperature resistance: -40° C to +250° C Permanent load – (colour change possible) Dry season:   At 20°C Dust dry: approx. 30 min. Grip-proof: approx. 60 min. Overpaintable: approx. 6 hours. Cured: approx. 24 hours.

Fertan Ferpox Epoxyprimer 400 ml Spray   Features: FERPOX is a 1-K epoxy primer Lead and chromate free temperature resistant from -40° C to + 250° C overcoatable FERPOX is applied like normal adhesive ground or primer particularly good adhesion to: Iron and steel Pre-treated aluminium hot-dip galvanized metal the ideal primer for all metals exposed to high stress or corrosion hazards: particularly high strength closed surface FERPOX can be injected (diluted) and coated Colour grey RAL 7012 400 millilitre spray can   Scope of application: Vehicle restoration: Subfloors Wheel arches Spray walls Frame and disc frames Battery holders etc.   Processing: FERPOX is applied like normal adhesive base or paint. Application is carried out by means of a brush, roller or spray gun. When applied with compressed air spray guns with max. Dilute 10% nitro dilution. When applying with a brush or roll, do not apply too high layer thicknesses, 1x thin layer is completely sufficient. Compressed air processing: Nozzle: 1. 5 Pressure: 2 – 4 bar Dilution: Nitro dilution (only) Theoretical yield: Different depending on the type of surface and processing. Yield: Film thickness Wet Dry Area 77μm 50 μm 6. 9 m2/kg 108 μm 70 μm 4. 8 m2/kg Technical data:   Delivery viscosity: approx. 150 sec. DIN 4 mm Density: approx. 1. 18 – 1. 24 kg/litre Overpaintable with 1-K and 2-K standard coatings: with 2-K max. 150 μm. Temperature resistance: -40° C to +250° C Permanent load – (colour change possible) Dry season:   At 20°C Dust dry: approx. 30 min. Grip-proof: approx. 60 min. Overpaintable: approx. 6 hours. Cured: approx. 24 hours.

Fertan Korrosionsschutzfett 1000 ml Dose Das FERTAN Korrosionsschutzfett ist ein sehr spezielles Fett, was die positiven Eigenschaften eines Fettes mit denen eines Wachses verbindet. Durch diese spezielle Zusammensetzung wird eine enormen Kriecheigenschaft ermöglicht welche bereits bei 20 °C bis zu 5 cm in Falzen, Spalten, Flansche und Blechdopplungen durchdringt. Diese verhindert jedoch, dass das Material bei Temperaturen über 40°C herauslaufen kann. Das Korrosionsschutzfett stellt einen extremen und dauerhaften Schutz der Karosseriebauteile gegen Korrosion dar und wird bei neuen Fahrzeugkarosserien, Oldtimern, Baufahrzeugen und landwirtschaftlichen Maschinen verwendet. Die Verträglichkeit mit vorhandenen, oft älteren, Schutzmaterialien ist bei vielen Schutzmaterialien gewährleistet. (wie z.B. Steinschlagschutz auf Harz und Bitumen Basis, Wachs Beschichtungen etc.).   Merkmale: Sehr guter Langzeitkorrosionsschutz Sehr gute Langzeitwirkung Hoher Festkörperbestandteil Dringt in Flansche, Fugen, Blechdoppelungen usw. perfekt bereits bei 20° C ein Milder angenehmer Geruch Kälteflexibler und dauerhaft elastischer Schutzfilm Bei ausreichender Schichtstärke mit Selbstheilungseffekt Kleinere Beschädigungen schließen sich selbsttätig   Verarbeitung: Verarbeitung mit Hohlraumdruckbecher-Pistole z.B. unsere TBS 222 (Artikelnr. 010022) Der Untergrund sollte frei von losem Material, sowie trocken und rostfrei sein Eventuell bereits vorhandene Korrosion mit FERTAN Rostkonverter sachgerecht entfernen Empfohlene Verarbeitungstemperatur 10 – 30° C Empfohlene Trockenschichtstärke ca. 50 µm. Eine höhere Schichtstärke, eventuell aufgebracht in einer zweiten Applikation, erhöht die Schutzwirkung   Lagerung und Haltbarkeit: Bei Temperaturen zwischen +10 bis +30° C mindest 24 Monate. Lagerung frostfrei.

Fertan Hansalin Manulin Hand cleaning cream   Features: powerful, deep-cleansing, oil-in-water emulsion suitable for dispenser-application, which easily removes stubborn dirt, such as synthetic resins, cellulose paints, lithography printing inks, oils, greases, even graphite oils and grease, tar, bitumen, rubber-residue etc. traditionally removed by solvent-based cleaners. primarily based on natural ingredients and contains natural cold-pressed oils and lanolin to care for the skin and maintain its moisture balance. Its deep cleaning action is enhanced by the addition of specially formulated micro-granules. dermatologist tested and is pH-balanced. environmentally friendly and uses only biodegradable surfactants economical to use, with only 2-3 mls being enough to clean the hands thoroughly. Instructions for use: Rub a little MANULIN into dry hands to loosen the dirt. Rinse thoroughly with water and dry. If water is not available, MANULIN can simply be wiped of with cloth.