Fertan Tapox 2-K Tank sealing TAPOX is the proven and durable, as well as very resistant 2-K tank interior coating. Features: Fuel resistant Temperature resistant, resistant to +80°C E. g. for lacquers. Extremely resistant. Suitable for all fuel cards (e. g. : motorcycle, car, boat, fuel oil tank, industrial tank). Fuel tanks made of steel have the property to rust easily. The reason is the MTBE (methyl tertiate butyl ester) added to the impact resistance in modern fuels. A special 2-C inner coating, which is resistant to fuels, provides a remedy. Tapox Klein (285ml): Maximum tank volume: Motorcycle 20l / Autotank 45l.   Benefits: Not released by petrol, diesel or ethanol Resistant to many acids and alkalis Temperature resistant up to +80 °C   Application: Before use, stir the product TAPOX very well, add hardener and mix to a completely thin coating. Please note that TAPOX is a resin and not a color and must therefore be stirred longer to obtain the completely thin mixture! Clean the tank very thoroughly before the inner coating, rust and protect it against new corrosion with FERTAN. Apply the TAPOX coating only to the completely dry tank. Pay close attention to processing instructions. Processing time of the mixed product, for interim storage at 0° – max 4° C, maximum 4 hours. Notes on error avoidance: Keep to the processing temperature (above 15° C). Hardener and stem must be mixed completely. Provide sufficient ventilation during curing (see instructions). TAPOX likes to settle more firmly on the bottom of the can. This does not affect the quality in any way, it may only be necessary to stir a little longer. Light pre-mixing is very useful and allows a better mixing of both components after the addition of the hardener, which is important for the adhesion of the final coating. Only optimally mixed components, at temperatures above 15°C, guarantee the perfect and fuel-resistant final coating with a very long service life. Dry season: At 20 °C Dust dry 15-30 min Handle-resistant 60-120 min Full 72 hours Processing tools: No processing tools required. (for commercial fuel tanks). For large tanks, which are accessible for example, an application is possible with the help of air tools or brushes/rollers. Air flow is mandatory.   Content: 285 ml Tapox sealing 160 ml TX-10 hardener

  Fertan Rust Converter, 1 Liter   The FERTAN rust converter is the perfect rust converter. With the FERTAN rust converter you can easily remove strong rust. For optimal rust removal.   Features: 1 litre standard dose for the removal of rust and corrosion of carbon steel for vehicles, vehicle parts and fuel tanks, car body cavities for metal constructions, ships, ship parts, port facilities for steel halls, conservatories and other carbon steel components Proven for decades in restoration the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallically clean, but not rust-free   Fertan Rust converter advantages: As a rust converter, FERTAN dissolves the existing rust layer (Fe3) and decomposes it into a non-reactive powder. The non-corrosive Fe2 layer underneath is protected with the new metal bond and the previously corroded metal can be provided with the required final protection within 6 months. This can be used in paint, varnish, wax, tar, zinc, epoxy resin, etc. e. be. FERTAN rust converter can be used successfully on slightly rusted, strong rust and also on bare metal. The protective effect is achieved in principle. The product is also water-based for environmental reasons. For this reason, the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallic clean, but not rust-free. Only with extremely strong rust layers, over 5 mm, a second treatment may be necessary. However, use FERTAN only at temperatures above 5°C and leave on for about 24 – 48 hours. Always clean the surface with water before the final treatment. The FERTAN rust converter can be used even on damp surfaces and is free of pollutants.   Application: FERTAN Rust converter Application: (Shake before use) Remove loose rust and prepare a smooth lacquerable surface for the surface to be painted later. (e. g. by grinding) Before applying FERTAN, it is important to clean surfaces of oil, grease, silicone and dirt. Apply FERTAN using a clean brush, roller or spray gun.   Temperature information: Allow FERTAN to act at temperatures above 20°C for 24 hours. In dry environment or direct sunlight, moisten slightly after 1-2 hours (fog moisture). At temperatures of 5 – 19° C, extend the reaction time to approx. 48 hours, or longer. Do not use in frost and temperatures below 5° C!   Surface turns black – blue violet Ideal for post-treatment after 6 months at the latest: Filler, primer (FERPOX, MM30), colour, cavity protection wash and underbody protection waxes (UBS 240), EP resins etc. Only rinse the surface with water before further treatment (the surface should not be damaged mechanically, otherwise the protective layer will be destroyed – no grinding, etc. ) This black, blue-violet surface can be overpainted with all conventional primers and varnishes, 1 litre of FERTAN is sufficient for approx. 12 – 15m2 surface when applied with a brush. FERTAN may cause stains on bright surfaces and absorbent surfaces, so cover them and wash splashes immediately with water, avoiding any open-pored material (e. g. wood, concrete, etc. ) that should not be processed. Clean tools after use with clear water. Wear protective clothing and follow safety instructions.    

  Fertan Rust Converter, 250 ml   The FERTAN rust converter is the perfect rust converter. With the FERTAN rust converter you can easily remove strong rust. For optimal rust removal.   Features: 250 millilitre spray gun for the removal of rust and corrosion of carbon steel for vehicles, vehicle parts and fuel tanks, car body cavities for metal constructions, ships, ship parts, port facilities for steel halls, conservatories and other carbon steel components Proven for decades in restoration the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallically clean, but not rust-free   Fertan Rust converter advantages: As a rust converter, FERTAN dissolves the existing rust layer (Fe3) and decomposes it into a non-reactive powder. The non-corrosive Fe2 layer underneath is protected with the new metal bond and the previously corroded metal can be provided with the required final protection within 6 months. This can be used in paint, varnish, wax, tar, zinc, epoxy resin, etc. e. be. FERTAN rust converter can be used successfully on slightly rusted, strong rust and also on bare metal. The protective effect is achieved in principle. The product is also water-based for environmental reasons. For this reason, the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallic clean, but not rust-free. Only with extremely strong rust layers, over 5 mm, a second treatment may be necessary. However, use FERTAN only at temperatures above 5°C and leave on for about 24 – 48 hours. Always clean the surface with water before the final treatment. The FERTAN rust converter can be used even on damp surfaces and is free of pollutants.   Application: FERTAN Rust converter Application: (Shake before use) Remove loose rust and prepare a smooth lacquerable surface for the surface to be painted later. (e. g. by grinding) Before applying FERTAN, it is important to clean surfaces of oil, grease, silicone and dirt. Apply FERTAN using a clean brush, roller or spray gun.   Temperature information: Allow FERTAN to act at temperatures above 20°C for 24 hours. In dry environment or direct sunlight, moisten slightly after 1-2 hours (fog moisture). At temperatures of 5 – 19° C, extend the reaction time to approx. 48 hours, or longer. Do not use in frost and temperatures below 5° C!   Surface turns black – blue violet Ideal for post-treatment after 6 months at the latest: Filler, primer (FERPOX, MM30), colour, cavity protection wash and underbody protection waxes (UBS 240), EP resins etc. Only rinse the surface with water before further treatment (the surface should not be damaged mechanically, otherwise the protective layer will be destroyed – no grinding, etc. ) This black, blue-violet surface can be overpainted with all conventional primers and varnishes, 1 litre of FERTAN is sufficient for approx. 12 – 15m2 surface when applied with a brush. FERTAN may cause stains on bright surfaces and absorbent surfaces, so cover them and wash splashes immediately with water, avoiding any open-pored material (e. g. wood, concrete, etc. ) that should not be processed. Clean tools after use with clear water. Wear protective clothing and follow safety instructions.    

Fertan FeDOGEL 750 ml Rust-Remover-Gel One of the most trusted product by industries and classic car enthusiast for rust treatments for over 38 years. FERTAN products have been bestselling rust removers, coatings and primers in Germany and several other European countries for several years now. FERTAN® RUST REMOVER GEL is perfect for the removal of rust and corrosion on metal parts, especially in hard to reach places. The gel can easily be applied using a brush or sponge and has a relatively short reaction time when compared to liquid solutions. RECOMMENDED FOR: Rust-proofing and maintenance inter-ventions on any material that rusts.   Features: Can be applied directly with brush or sponge for hard-to-reach areas Water-based, non-toxic & biodegradable Completely removes rust, does not mask it Content (metric): 750 ml Item no.: 23530   Anwendung: Der Gel-Film in ca. 3-5 mm Stärke aufgetragen löst die Korrosion. Vor Gebrauch alle Sicherheitshinweise lesen und verstehen. Schutzkleidung, Augenschutz/Gesichtsschutz und Schutzhandschuhe tragen. Auftrag mit Pinsel oder Schwamm Reaktionszeit 10-60 Minuten. Vor Austrocknung schützen. Rückstandslos mit Wasser, ggfs. mit Bürste oder Schwamm reinigen. Bei sehr starker Korrosion Vorgang wenn notwendig wiederholen. Originalgebinde dicht verschlossen halten und vor direktem Sonnenlicht geschützt bei 5°C bic 25°C lagern. Anbruchgebinde kurzfristig verarbeiten. Gereinigte Teile möglichst schnell mit geeignetem Rostschutz vor erneuter Korrosion schützen. Z.B. mit MM30, FERPOX Epoxy Primer, Farbe, Wachs etc.   Gefahrenhinweise: Einstufung gemäß Verordnung (EG) Nr. 1907/2006 Verursacht schwere Augenreizung. Gesundheitsschädlich bei Einatmen Sicherheitshinweise Ist ärztlicher Rat erforderlich, Verpackung oder Kennzeichnungsetikett bereithalten. Darf nicht in die Hände von Kindern gelangen. Aerosol/Sprühnebel nicht einatmen. Gummihandschuhe., Dicht schließende Schutzbrille. tragen. BEI EINATMEN: Die Person an die frische Luft bringen und für ungehinderte Atmung sorgen. BEI KONTAKT MIT DEN AUGEN: Einige Minuten lang behutsam mit Wasser spülen. Vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülen. Bei anhaltender Augenreizung: Ärztlichen Rat einholen/ärztliche Hilfe hinzuziehen.