Fertan Spray-head for 1 l   Features: Spray-head for 1 l Spray device for self-filling with 2 spray heads Probe diameter only Ø 4,2 mm Weight: 0,22 kg

BGS 9406 Plastic Plug Assortment, 58 pcs. Features:BGS 9406 Plastic Plug Assortment, 58 pcs.for closing the following bore sizes:10 plugs Ø 10.0 mm10 plugs Ø 13.4 mm10 plugs Ø 13.5 mm8 plugs Ø 19.4 mm10 plugs Ø 19.5 mm10 plugs Ø 22.2 mmin assortment box Technical features:Gross weight: 140 gPackaging suitable for wall hanging: YesEAN: 4026947094069

  Fertan Rust Converter, 1 Liter   The FERTAN rust converter is the perfect rust converter. With the FERTAN rust converter you can easily remove strong rust. For optimal rust removal.   Features: 1 litre standard dose for the removal of rust and corrosion of carbon steel for vehicles, vehicle parts and fuel tanks, car body cavities for metal constructions, ships, ship parts, port facilities for steel halls, conservatories and other carbon steel components Proven for decades in restoration the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallically clean, but not rust-free   Fertan Rust converter advantages: As a rust converter, FERTAN dissolves the existing rust layer (Fe3) and decomposes it into a non-reactive powder. The non-corrosive Fe2 layer underneath is protected with the new metal bond and the previously corroded metal can be provided with the required final protection within 6 months. This can be used in paint, varnish, wax, tar, zinc, epoxy resin, etc. e. be. FERTAN rust converter can be used successfully on slightly rusted, strong rust and also on bare metal. The protective effect is achieved in principle. The product is also water-based for environmental reasons. For this reason, the surface to be treated must be free of dirt, oil, grease and silicone, i. e. metallic clean, but not rust-free. Only with extremely strong rust layers, over 5 mm, a second treatment may be necessary. However, use FERTAN only at temperatures above 5°C and leave on for about 24 – 48 hours. Always clean the surface with water before the final treatment. The FERTAN rust converter can be used even on damp surfaces and is free of pollutants.   Application: FERTAN Rust converter Application: (Shake before use) Remove loose rust and prepare a smooth lacquerable surface for the surface to be painted later. (e. g. by grinding) Before applying FERTAN, it is important to clean surfaces of oil, grease, silicone and dirt. Apply FERTAN using a clean brush, roller or spray gun.   Temperature information: Allow FERTAN to act at temperatures above 20°C for 24 hours. In dry environment or direct sunlight, moisten slightly after 1-2 hours (fog moisture). At temperatures of 5 – 19° C, extend the reaction time to approx. 48 hours, or longer. Do not use in frost and temperatures below 5° C!   Surface turns black – blue violet Ideal for post-treatment after 6 months at the latest: Filler, primer (FERPOX, MM30), colour, cavity protection wash and underbody protection waxes (UBS 240), EP resins etc. Only rinse the surface with water before further treatment (the surface should not be damaged mechanically, otherwise the protective layer will be destroyed – no grinding, etc. ) This black, blue-violet surface can be overpainted with all conventional primers and varnishes, 1 litre of FERTAN is sufficient for approx. 12 – 15m2 surface when applied with a brush. FERTAN may cause stains on bright surfaces and absorbent surfaces, so cover them and wash splashes immediately with water, avoiding any open-pored material (e. g. wood, concrete, etc. ) that should not be processed. Clean tools after use with clear water. Wear protective clothing and follow safety instructions.