NET-TROL – Holzreiniger & Aufheller
Eigenschaften
dringt tief in die Poren des Untergrundes ein
beseitigt tiefsitzende Verschmutzung
gibt dem Holz seinen ursprünglichen Farbton zurück
intakte Anstriche werden nicht beschädigt oder entfernt
enthält Oxalsäure
biologisch abbaubar
Einsatzgebiete
vergrautes Holz (auch druckimprägniertes Holz), z.B. Gartenmöbel, Terrassen, Beckenumrandungen, Fassadenverkleidungen, Fenster, Türen
Schiff-Decks, ohne Dichtungen oder Verleimungen zu schädigen
Beseitigung witterungsbedingter Verfärbung und Stockflecken
Abwaschen von oberflächlich austretenden Holzinhaltstoffen
»selektive« Reinigung ungleichmäßig verwitterter Flächen (z. B. bei Dachüberständen)
intakte Anstriche und nicht vergraute Bereiche:
-intensive Reinigung, ohne den Farbton zu ändern
vergraute Bereiche: Entgrauung hin zum Originalfarbton
Gummiauflage passend für Nußbaum, Ami Hebebühnen
Merkmale:
Durchmesser außen: 125 mm
Durchmesser a innen: 120 mm
Mit 2 Bohrungen
mit umlaufenden Gummirand
mit einvulkanisiertem Stahlteller
b = 90 mm
d = 24 mm
0,30 kg
OWATROL, 300 ml Spray Can, Paint Conditioner & Rust Inhibitor
Features:
Suitable for a multitude of uses, Owatrol Oil performs in a variety of situations, from protecting metal from rust to penetrating and enhancing a wood's natural grain. As a colourless solution, Owatrol Oil is a versatile product - ideal as a rust inhibitor, paint conditioner, penetrating oil and more.
OWATROL-Oil protects metals against rust, stopping corrosion at source and protecting the base metal form further rust.
As a colourless solution, Owatrol Oil penetrates deep into the sound metal, protecting from corrosion and driving out any air and moisture to stabilise the material. When mixed with any paint, Owatrol Oil improves workability and paint-flow. Owatrol Oil enhances the viscosity of the mixture, resulting in an improved application ideal for exceptionally cold, warm or windy conditions.
Owatrol Oil also makes alkyd based paints rust inhibiting, further enhancing the solution. Owatrol Oil also improves the 'hiding power' of paint, replacing potentially damaging thinners. As a colourless solution, Owatrol Oil maintains the natural look to any material it is applied to. It offers excellent adhesion to materials such as woods and metals such as zinc, aluminium and galvanised surfaces. The advanced adhesion of Owatrol Oil makes it an ideal base for priming or finishing materials, and allows paint to be applied directly onto corroded or rusted surfaces. Owatrol Oil offers a heat resistance up to 175+oC.
Applications for use:
Designed for ferrous and non ferrous metals. (may be applied on wood, plastics, glass)
Lightly to heavily rusted surfaces.
On new surfaces, use Owatrol AP60
May be used in any oil based paints, air drying alkyds, lacquers and varnishes, one component urethanes and asphalt / petroleum based paints. May be mixed with oil based stains/paint to improve impregnation of wood and protection of metal surfaces (hinges and fittings)
Do not mix with quick drying paints (car paints), chlorinated rubber paints, with two components paints and water based paints
Application instructions:
Surface must be clean, dry and free from grease, oil and dirt!
To act as a rust inhibitor within paint, mix 25% Owatrol oil with 75% paint
For improved paint workflow, mix 5-10% Owatrol oil within the paint
Coverage: 1 litre covers approximately 18 square metres
Application tools: Brush, roller or spray; Drying time: 12 hours; Clean-up: White Spirit
Features:
Suitable for a multitude of uses
From protecting metal from rust to penetrating and enhancing a wood's natural grain.
As a colourless solution, Owatrol Oil is a versatile product - ideal as a rust inhibitor, paint conditioner, penetrating oil and more.
OWATROL-Oil protects metals against rust, stopping corrosion at source and protecting the base metal form further rust.
As a colourless solution, Owatrol Oil penetrates deep into the sound metal, protecting from corrosion and driving out any air and moisture to stabilise the material. When mixed with any paint, Owatrol Oil improves workability and paint-flow. Owatrol Oil enhances the viscosity of the mixture, resulting in an improved application ideal for exceptionally cold, warm or windy conditions.
Owatrol Oil also makes alkyd based paints rust inhibiting, further enhancing the solution. Owatrol Oil also improves the 'hiding power' of paint, replacing potentially damaging thinners. As a colourless solution, Owatrol Oil maintains the natural look to any material it is applied to. It offers excellent adhesion to materials such as woods and metals such as zinc, aluminium and galvanised surfaces. The advanced adhesion of Owatrol Oil makes it an ideal base for priming or finishing materials, and allows paint to be applied directly onto corroded or rusted surfaces. Owatrol Oil offers a heat resistance up to 175+oC.
Applications for use
Designed for ferrous and non ferrous metals. (may be applied on wood, plastics, glass)
Lightly to heavily rusted surfaces.
On new surfaces, use Owatrol AP60
May be used in any oil based paints, air drying alkyds, lacquers and varnishes, one component urethanes and asphalt / petroleum based paints. May be mixed with oil based stains/paint to improve impregnation of wood and protection of metal surfaces (hinges and fittings)
Do not mix with quick drying paints (car paints), chlorinated rubber paints, with two components paints and water based paints
Application instructions
Application tools: Brush, roller or spray; Drying time: 12 hours; Clean-up: White Spirit
Coverage: 1 litre covers approximately 18 square metres
For improved paint workflow, mix 5-10% Owatrol oil within the paint
To act as a rust inhibitor within paint, mix 25% Owatrol oil with 75% paint
Surface must be clean, dry and free from grease, oil and dirt!
OWATROL, 1 l, Paint Conditioner & Rust Inhibitor
Features:
Suitable for a multitude of uses
From protecting metal from rust to penetrating and enhancing a wood's natural grain.
As a colourless solution, Owatrol Oil is a versatile product - ideal as a rust inhibitor, paint conditioner, penetrating oil and more.
OWATROL-Oil protects metals against rust, stopping corrosion at source and protecting the base metal form further rust.
As a colourless solution, Owatrol Oil penetrates deep into the sound metal, protecting from corrosion and driving out any air and moisture to stabilise the material. When mixed with any paint, Owatrol Oil improves workability and paint-flow. Owatrol Oil enhances the viscosity of the mixture, resulting in an improved application ideal for exceptionally cold, warm or windy conditions.
Owatrol Oil also makes alkyd based paints rust inhibiting, further enhancing the solution. Owatrol Oil also improves the 'hiding power' of paint, replacing potentially damaging thinners. As a colourless solution, Owatrol Oil maintains the natural look to any material it is applied to. It offers excellent adhesion to materials such as woods and metals such as zinc, aluminium and galvanised surfaces. The advanced adhesion of Owatrol Oil makes it an ideal base for priming or finishing materials, and allows paint to be applied directly onto corroded or rusted surfaces. Owatrol Oil offers a heat resistance up to 175+oC.
Applications for use
Designed for ferrous and non ferrous metals. (may be applied on wood, plastics, glass)
Lightly to heavily rusted surfaces.
On new surfaces, use Owatrol AP60
May be used in any oil based paints, air drying alkyds, lacquers and varnishes, one component urethanes and asphalt / petroleum based paints. May be mixed with oil based stains/paint to improve impregnation of wood and protection of metal surfaces (hinges and fittings)
Do not mix with quick drying paints (car paints), chlorinated rubber paints, with two components paints and water based paints
Application instructions
Application tools: Brush, roller or spray; Drying time: 12 hours; Clean-up: White Spirit
Coverage: 1 litre covers approximately 18 square metres
For improved paint workflow, mix 5-10% Owatrol oil within the paint
To act as a rust inhibitor within paint, mix 25% Owatrol oil with 75% paint
Surface must be clean, dry and free from grease, oil and dirt!
PERMA FILM ALUMINIUM SILVER 1 liter
Perma Film from Hodt Fluid Film is an anticorrosive coating for all bare, rusted or with
old coatings and also non-ferrous metals after appropriate pretreatment.
1 liter aluminum silver
Rust protection and paint
Perfect in combination with Fluid FIlm
Easy application
Features
Rust protection and painting in one;
can be applied directly in the system with FLUID FILM Liquid A/ NAS or AS-R
(spray) on rust.
Thanks to its extraordinary penetration properties, FLUID FILM enables
penetration properties, FLUID FILM allows a thorough wetting and
encapsulation of rust and/or existing coatings;
Long-term rust protection;
good wettability of deep-pored substrates and also joints and
seams (seam sealing) in the system with FLUID FILM as primer;
high layer thicknesses are easy to apply by spraying
hardly any overspray;
low material loss
Application:
Surface preparation:
Bare ferrous metals:
Sand very smooth surfaces. Remove grinding dust. Clean surface carefully with solvent.
Rusted ferrous metals:
Remove loose particles with wire brush or clean by high pressure washing. Allow to dry after washing.
Zinc or galvanized surfaces:
As weathering progresses, zinc or galvanized surfaces become dull and rough, and zinc salts form on the surface (white coating). This coating must be removed before coating, otherwise no adhesion is possible. For this purpose, an "ammoniacal wetting agent wash" is used. This consists of water and ammonia solution (10:1) with a few drops of washing-up liquid. With this solution and abrasive fleece, the surface is carefully worked until a grayish foam is formed. Leave to act for 10 minutes, then rinse thoroughly with water and allow to dry.
Application:
A dry film thickness of at least 150 μm is a prerequisite for safe
layer thickness of at least 150 μm. (Wet film thickness 250 μm).
This film thickness is achieved after 2 - 3 applications when applying by brush or roller, and after
2 - 3 applications, by spraying after 1 application.
PERMA FILM is very thixotropic and can therefore be applied without sagging in the
up to a wet film thickness of 250 μm in one application without
applied in one working step.
For higher film thicknesses, several coats are necessary,
For higher film thicknesses, several coats are necessary.
air must be ensured.
Substrates:
Bare, rusted or with old coatings provided ferrous metals.
Non-ferrous metals after previous treatment
Wooden subfloor areas
The use of the primer FLUID FILM Liquid A/NAS or
AS-R fulfills the following tasks:
Penetration to the underside through dense rust or existing
Wax or bitumen based coatings;
Blocking loose edges, cracks and folds;
The application of FLUID FILM also eliminates
possible stresses due to excessive shrinkage and hardening of the PERMA FILM
and hardening of the PERMA FILM coating and prevents the layers from
that the layers peel off from the rusty substrate;
Any residual moisture is displaced by the penetration of FLUID
FILM is displaced.
A low layer thickness reduces the risk that an excessive
of the primer will not penetrate into the subsequent PERMA FILM coat, thus
and thus prolongs or even prevents curing.
PERMA FILM ALUMINIUM SILVER 1 liter
Perma Film from Hodt Fluid Film is an anticorrosive coating for all bare, rusted or with
old coatings and also non-ferrous metals after appropriate pretreatment.
3 liter aluminum silver
Rust protection and paint
Perfect in combination with Fluid FIlm
Easy application
Features
Rust protection and painting in one;
can be applied directly in the system with FLUID FILM Liquid A/ NAS or AS-R
(spray) on rust.
Thanks to its extraordinary penetration properties, FLUID FILM enables
penetration properties, FLUID FILM allows a thorough wetting and
encapsulation of rust and/or existing coatings;
Long-term rust protection;
good wettability of deep-pored substrates and also joints and
seams (seam sealing) in the system with FLUID FILM as primer;
high layer thicknesses are easy to apply by spraying
hardly any overspray;
low material loss
Application:
Surface preparation:
Bare ferrous metals:
Sand very smooth surfaces. Remove grinding dust. Clean surface carefully with solvent.
Rusted ferrous metals:
Remove loose particles with wire brush or clean by high pressure washing. Allow to dry after washing.
Zinc or galvanized surfaces:
As weathering progresses, zinc or galvanized surfaces become dull and rough, and zinc salts form on the surface (white coating). This coating must be removed before coating, otherwise no adhesion is possible. For this purpose, an "ammoniacal wetting agent wash" is used. This consists of water and ammonia solution (10:1) with a few drops of washing-up liquid. With this solution and abrasive fleece, the surface is carefully worked until a grayish foam is formed. Leave to act for 10 minutes, then rinse thoroughly with water and allow to dry.
Application:
A dry film thickness of at least 150 μm is a prerequisite for safe
layer thickness of at least 150 μm. (Wet film thickness 250 μm).
This film thickness is achieved after 2 - 3 applications when applying by brush or roller, and after
2 - 3 applications, by spraying after 1 application.
PERMA FILM is very thixotropic and can therefore be applied without sagging in the
up to a wet film thickness of 250 μm in one application without
applied in one working step.
For higher film thicknesses, several coats are necessary,
For higher film thicknesses, several coats are necessary.
air must be ensured.
Substrates:
Bare, rusted or with old coatings provided ferrous metals.
Non-ferrous metals after previous treatment
Wooden subfloor areas
The use of the primer FLUID FILM Liquid A/NAS or
AS-R fulfills the following tasks:
Penetration to the underside through dense rust or existing
Wax or bitumen based coatings;
Blocking loose edges, cracks and folds;
The application of FLUID FILM also eliminates
possible stresses due to excessive shrinkage and hardening of the PERMA FILM
and hardening of the PERMA FILM coating and prevents the layers from
that the layers peel off from the rusty substrate;
Any residual moisture is displaced by the penetration of FLUID
FILM is displaced.
A low layer thickness reduces the risk that an excessive
of the primer will not penetrate into the subsequent PERMA FILM coat, thus
and thus prolongs or even prevents curing.
PERMA FILM BLACK 3 liter
Perma Film from Hodt Fluid Film is an anticorrosive coating for all bare, rusted or with
old coatings and also non-ferrous metals after appropriate pretreatment.
3 liter black
Rust protection and paint
Perfect in combination with Fluid FIlm
Easy application
Features
Rust protection and painting in one;
can be applied directly in the system with FLUID FILM Liquid A/ NAS or AS-R
(spray) on rust.
Thanks to its extraordinary penetration properties, FLUID FILM enables
penetration properties, FLUID FILM allows a thorough wetting and
encapsulation of rust and/or existing coatings;
Long-term rust protection;
good wettability of deep-pored substrates and also joints and
seams (seam sealing) in the system with FLUID FILM as primer;
high layer thicknesses are easy to apply by spraying
hardly any overspray;
low material loss
Application:
Surface preparation:
Bare ferrous metals:
Sand very smooth surfaces. Remove grinding dust. Clean surface carefully with solvent.
Rusted ferrous metals:
Remove loose particles with wire brush or clean by high pressure washing. Allow to dry after washing.
Zinc or galvanized surfaces:
As weathering progresses, zinc or galvanized surfaces become dull and rough, and zinc salts form on the surface (white coating). This coating must be removed before coating, otherwise no adhesion is possible. For this purpose, an "ammoniacal wetting agent wash" is used. This consists of water and ammonia solution (10:1) with a few drops of washing-up liquid. With this solution and abrasive fleece, the surface is carefully worked until a grayish foam is formed. Leave to act for 10 minutes, then rinse thoroughly with water and allow to dry.
Application:
A dry film thickness of at least 150 μm is a prerequisite for safe
layer thickness of at least 150 μm. (Wet film thickness 250 μm).
This film thickness is achieved after 2 - 3 applications when applying by brush or roller, and after
2 - 3 applications, by spraying after 1 application.
PERMA FILM is very thixotropic and can therefore be applied without sagging in the
up to a wet film thickness of 250 μm in one application without
applied in one working step.
For higher film thicknesses, several coats are necessary,
For higher film thicknesses, several coats are necessary.
air must be ensured.
Substrates:
Bare, rusted or with old coatings provided ferrous metals.
Non-ferrous metals after previous treatment
Wooden subfloor areas
The use of the primer FLUID FILM Liquid A/NAS or
AS-R fulfills the following tasks:
Penetration to the underside through dense rust or existing
Wax or bitumen based coatings;
Blocking loose edges, cracks and folds;
The application of FLUID FILM also eliminates
possible stresses due to excessive shrinkage and hardening of the PERMA FILM
and hardening of the PERMA FILM coating and prevents the layers from
that the layers peel off from the rusty substrate;
Any residual moisture is displaced by the penetration of FLUID
FILM is displaced.
A low layer thickness reduces the risk that an excessive
of the primer will not penetrate into the subsequent PERMA FILM coat, thus
and thus prolongs or even prevents curing.
PERMA FILM BLACK 1 liter
Perma Film from Hodt Fluid Film is an anticorrosive coating for all bare, rusted or with
old coatings and also non-ferrous metals after appropriate pretreatment.
1 liter black
Rust protection and paint
Perfect in combination with Fluid FIlm
Easy application
Features
Rust protection and painting in one;
can be applied directly in the system with FLUID FILM Liquid A/ NAS or AS-R
(spray) on rust.
Thanks to its extraordinary penetration properties, FLUID FILM enables
penetration properties, FLUID FILM allows a thorough wetting and
encapsulation of rust and/or existing coatings;
Long-term rust protection;
good wettability of deep-pored substrates and also joints and
seams (seam sealing) in the system with FLUID FILM as primer;
high layer thicknesses are easy to apply by spraying
hardly any overspray;
low material loss
Application:
Surface preparation:
Bare ferrous metals:
Sand very smooth surfaces. Remove grinding dust. Clean surface carefully with solvent.
Rusted ferrous metals:
Remove loose particles with wire brush or clean by high pressure washing. Allow to dry after washing.
Zinc or galvanized surfaces:
As weathering progresses, zinc or galvanized surfaces become dull and rough, and zinc salts form on the surface (white coating). This coating must be removed before coating, otherwise no adhesion is possible. For this purpose, an "ammoniacal wetting agent wash" is used. This consists of water and ammonia solution (10:1) with a few drops of washing-up liquid. With this solution and abrasive fleece, the surface is carefully worked until a grayish foam is formed. Leave to act for 10 minutes, then rinse thoroughly with water and allow to dry.
Application:
A dry film thickness of at least 150 μm is a prerequisite for safe
layer thickness of at least 150 μm. (Wet film thickness 250 μm).
This film thickness is achieved after 2 - 3 applications when applying by brush or roller, and after
2 - 3 applications, by spraying after 1 application.
PERMA FILM is very thixotropic and can therefore be applied without sagging in the
up to a wet film thickness of 250 μm in one application without
applied in one working step.
For higher film thicknesses, several coats are necessary,
For higher film thicknesses, several coats are necessary.
air must be ensured.
Substrates:
Bare, rusted or with old coatings provided ferrous metals.
Non-ferrous metals after previous treatment
Wooden subfloor areas
The use of the primer FLUID FILM Liquid A/NAS or
AS-R fulfills the following tasks:
Penetration to the underside through dense rust or existing
Wax or bitumen based coatings;
Blocking loose edges, cracks and folds;
The application of FLUID FILM also eliminates
possible stresses due to excessive shrinkage and hardening of the PERMA FILM
and hardening of the PERMA FILM coating and prevents the layers from
that the layers peel off from the rusty substrate;
Any residual moisture is displaced by the penetration of FLUID
FILM is displaced.
A low layer thickness reduces the risk that an excessive
of the primer will not penetrate into the subsequent PERMA FILM coat, thus
and thus prolongs or even prevents curing.
PERMA FILM TRANSPARENT 1 liter
Perma Film from Hodt Fluid Film is an anticorrosive coating for all bare, rusted or with
old coatings and also non-ferrous metals after appropriate pretreatment.
1 liter transparent
Rust protection and paint
Perfect in combination with Fluid FIlm
Easy application
Features
Rust protection and painting in one;
can be applied directly in the system with FLUID FILM Liquid A/ NAS or AS-R
(spray) on rust.
Thanks to its extraordinary penetration properties, FLUID FILM enables
penetration properties, FLUID FILM allows a thorough wetting and
encapsulation of rust and/or existing coatings;
Long-term rust protection;
good wettability of deep-pored substrates and also joints and
seams (seam sealing) in the system with FLUID FILM as primer;
high layer thicknesses are easy to apply by spraying
hardly any overspray;
low material loss
Application:
Surface preparation:
Bare ferrous metals:
Sand very smooth surfaces. Remove grinding dust. Clean surface carefully with solvent.
Rusted ferrous metals:
Remove loose particles with wire brush or clean by high pressure washing. Allow to dry after washing.
Zinc or galvanized surfaces:
As weathering progresses, zinc or galvanized surfaces become dull and rough, and zinc salts form on the surface (white coating). This coating must be removed before coating, otherwise no adhesion is possible. For this purpose, an "ammoniacal wetting agent wash" is used. This consists of water and ammonia solution (10:1) with a few drops of washing-up liquid. With this solution and abrasive fleece, the surface is carefully worked until a grayish foam is formed. Leave to act for 10 minutes, then rinse thoroughly with water and allow to dry.
Application:
A dry film thickness of at least 150 μm is a prerequisite for safe
layer thickness of at least 150 μm. (Wet film thickness 250 μm).
This film thickness is achieved after 2 - 3 applications when applying by brush or roller, and after
2 - 3 applications, by spraying after 1 application.
PERMA FILM is very thixotropic and can therefore be applied without sagging in the
up to a wet film thickness of 250 μm in one application without
applied in one working step.
For higher film thicknesses, several coats are necessary,
For higher film thicknesses, several coats are necessary.
air must be ensured.
Substrates:
Bare, rusted or with old coatings provided ferrous metals.
Non-ferrous metals after previous treatment
Wooden subfloor areas
The use of the primer FLUID FILM Liquid A/NAS or
AS-R fulfills the following tasks:
Penetration to the underside through dense rust or existing
Wax or bitumen based coatings;
Blocking loose edges, cracks and folds;
The application of FLUID FILM also eliminates
possible stresses due to excessive shrinkage and hardening of the PERMA FILM
and hardening of the PERMA FILM coating and prevents the layers from
that the layers peel off from the rusty substrate;
Any residual moisture is displaced by the penetration of FLUID
FILM is displaced.
A low layer thickness reduces the risk that an excessive
of the primer will not penetrate into the subsequent PERMA FILM coat, thus
and thus prolongs or even prevents curing.
PERMA FILM TRANSPARENT 3 liter
Perma Film from Hodt Fluid Film is an anticorrosive coating for all bare, rusted or with
old coatings and also non-ferrous metals after appropriate pretreatment.
3 liter transparent
Rust protection and paint
Perfect in combination with Fluid FIlm
Easy application
Features
Rust protection and painting in one;
can be applied directly in the system with FLUID FILM Liquid A/ NAS or AS-R
(spray) on rust.
Thanks to its extraordinary penetration properties, FLUID FILM enables
penetration properties, FLUID FILM allows a thorough wetting and
encapsulation of rust and/or existing coatings;
Long-term rust protection;
good wettability of deep-pored substrates and also joints and
seams (seam sealing) in the system with FLUID FILM as primer;
high layer thicknesses are easy to apply by spraying
hardly any overspray;
low material loss
Application:
Surface preparation:
Bare ferrous metals:
Sand very smooth surfaces. Remove grinding dust. Clean surface carefully with solvent.
Rusted ferrous metals:
Remove loose particles with wire brush or clean by high pressure washing. Allow to dry after washing.
Zinc or galvanized surfaces:
As weathering progresses, zinc or galvanized surfaces become dull and rough, and zinc salts form on the surface (white coating). This coating must be removed before coating, otherwise no adhesion is possible. For this purpose, an "ammoniacal wetting agent wash" is used. This consists of water and ammonia solution (10:1) with a few drops of washing-up liquid. With this solution and abrasive fleece, the surface is carefully worked until a grayish foam is formed. Leave to act for 10 minutes, then rinse thoroughly with water and allow to dry.
Application:
A dry film thickness of at least 150 μm is a prerequisite for safe
layer thickness of at least 150 μm. (Wet film thickness 250 μm).
This film thickness is achieved after 2 - 3 applications when applying by brush or roller, and after
2 - 3 applications, by spraying after 1 application.
PERMA FILM is very thixotropic and can therefore be applied without sagging in the
up to a wet film thickness of 250 μm in one application without
applied in one working step.
For higher film thicknesses, several coats are necessary,
For higher film thicknesses, several coats are necessary.
air must be ensured.
Substrates:
Bare, rusted or with old coatings provided ferrous metals.
Non-ferrous metals after previous treatment
Wooden subfloor areas
The use of the primer FLUID FILM Liquid A/NAS or
AS-R fulfills the following tasks:
Penetration to the underside through dense rust or existing
Wax or bitumen based coatings;
Blocking loose edges, cracks and folds;
The application of FLUID FILM also eliminates
possible stresses due to excessive shrinkage and hardening of the PERMA FILM
and hardening of the PERMA FILM coating and prevents the layers from
that the layers peel off from the rusty substrate;
Any residual moisture is displaced by the penetration of FLUID
FILM is displaced.
A low layer thickness reduces the risk that an excessive
of the primer will not penetrate into the subsequent PERMA FILM coat, thus
and thus prolongs or even prevents curing.
Tripelpaste für Alu und Buntmetalle
Unsere Polierpasten werden in Blöcken zu 300 g geliefert.
Man hält sie an die rotierende Scheibe, bis sich daran etwas Paste abgesetzt hat. Dann kann mit dem Polieren begonnen werden.
Die Abstufung von grob nach fein erfolgt bei diesem Verfahren nicht über die Paste, sondern über die Scheiben:
Sisal (grob) zum Vorpolieren, Nessel zum Polieren und Flanell (fein) zum Glänzen.
Hochglanzpaste für Stahl
Unsere Polierpasten werden in Blöcken zu 300 g geliefert.
Man hält sie an die rotierende Scheibe, bis sich daran etwas Paste abgesetzt hat. Dann kann mit dem Polieren begonnen werden.
Die Abstufung von grob nach fein erfolgt bei diesem Verfahren nicht über die Paste, sondern über die Scheiben:
Sisal (grob) zum Vorpolieren, Nessel zum Polieren und Flanell (fein) zum Glänzen.
Polierscheibe 125 mm Sisal
Spitzenqualität aus Deutschland
Für den Profibereich
Anwendung: Die Polierpaste wird an die rotierende Scheibe gehalten, bis sich etwas Material daran abgesetzt hat. Dann wird mit der Scheibe das Material poliert.
Die Abstufung erfolgt dabei nicht über die Pasten, sondern über die Scheiben: Sisal zum Vorpolieren, Nessel zum Polieren und Flanell (dann oft ohne Pastenzusatz) zum Glänzen.
Die Scheiben werden entweder über einen Spanndorn in die Bohrmaschine, oder auf einen Polierbock gespannt.
Abmessungen:
Durchmesser: 125 mm
Bohrung: 10 mm
Dicke: 15 mm
Polierscheibe 150 mm Flanell
Anwendung: Die Polierpaste wird an die rotierende Scheibe gehalten, bis sich etwas Material daran abgesetzt hat. Dann wird mit der Scheibe das Material poliert.
Die Abstufung erfolgt dabei nicht über die Pasten, sondern über die Scheiben: Sisal zum Vorpolieren, Nessel zum Polieren und Flanell (dann oft ohne Pastenzusatz) zum Glänzen.
Die Scheiben werden entweder über einen Spanndorn in die Bohrmaschine, oder auf einen Polierbock gespannt.
Abmessungen:
Durchmesser: 150 mm
Bohrung: 12 mm
Dicke: 20 mm
Polierscheibe 150 mm Nessel
Anwendung: Die Polierpaste wird an die rotierende Scheibe gehalten, bis sich etwas Material daran abgesetzt hat. Dann wird mit der Scheibe das Material poliert.
Die Abstufung erfolgt dabei nicht über die Pasten, sondern über die Scheiben: Sisal zum Vorpolieren, Nessel zum Polieren und Flanell (dann oft ohne Pastenzusatz) zum Glänzen.
Die Scheiben werden entweder über einen Spanndorn in die Bohrmaschine, oder auf einen Polierbock gespannt.
Abmessungen:
Durchmesser: 150 mm
Bohrung: 12 mm
Dicke: 20 mm
Polierscheibe 200 mm Nessel
Anwendung: Die Polierpaste wird an die rotierende Scheibe gehalten, bis sich etwas Material daran abgesetzt hat. Dann wird mit der Scheibe das Material poliert.
Die Abstufung erfolgt dabei nicht über die Pasten, sondern über die Scheiben: Sisal zum Vorpolieren, Nessel zum Polieren und Flanell (dann oft ohne Pastenzusatz) zum Glänzen.
Die Scheiben werden entweder über einen Spanndorn in die Bohrmaschine, oder auf einen Polierbock gespannt.
Abmessungen:
Durchmesser: 200 mm
Bohrung: 12 mm
Dicke: 25 mm
