FLUID FILM AS-R Probe, 600 mm
Features:
FLUID FILM AS-R probe 600 mm for usage in longer cavities
60 cm long extension spray with a 3-round nozzle jet
Delivery without can
FLUID FILM Gel BN 1 liter
FLUID Film Gel BN is a solvent-free, soft coating material based on lanolin, environmentally friendly and physiologically harmless.
1 liter
Low environmental impact
Uncomplicated processing
Application by trowel, brush or roller possible
Features
Solvent-free, therefore considerably less environmental impact during processing, greater safety in operation.
Economical to use and uncomplicated to process. In thickness of up to more than 1,000 μm can be applied in a single operation can be applied (by airless spraying).
Can also be applied by trowel, brush or roller.
Cost-effective method of spraying by means of lances, which in the majority of in the majority of cases it is not necessary to erect a scaffold.
1-component product with excellent adhesion, even on intact penetrates residual rust excellently; layer rust that is not removed will be fall off from the metallic substrate after some time!
Renewal coatings can be applied after removal of all loose mud, standing water, can be immediately applied with FLUID
FILM can be applied.
Corrosion protection of steel parts and other metal parts during transport.
Storage and processing in the manufacturing plant.
Observance of the dew point during processing is not necessary, as long as no condensation can be detected.
Highest resistance to aqueous media.
Temperature stable from -45°C (248 K) to approx. 70°C (3 43 K),
If the coating is damaged, FLUID FILM Gel B exhibits a limited
limited self-healing effect.
Surface preparation:
The surfaces must be dry, free from dirt and loose components such as rust and old coatings. For damp-wet surfaces, an adhesive layer of FLUID FILM Gel B can be rubbed in using a hard brush.
Remove dirt and loose components by high pressure washing, sticking or brushing. Laminates layer rust from the metallic substrate.
On surfaces where the water flow exceeds 3 m/sec (e.g. under the inlet and outlet funnels), a curing coating suitable for ballast water tanks should be applied. On surfaces exposed to high water turbulence, e.g. tank tops in DB tanks, the FLUID FILM coating can be strengthened by applying an additional layer of PERMA FILM. In this case, FLUID FILM should have a layer thickness of approx. 200 μm and PERMA FILM a layer thickness of 200 μm (wet).
Application data:
Applied by
Amount of coats
Average film thickness in μm
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
0 - 1
Roller
1
80
0,08
12
0 - 1
Pneumatical spraying
1
600 - 1000
0,6 / 1,0
1,6 / 1,0
0,8 - 1
Airless spraying
1
600 - 1000
0,6 / 1,0
1,6 / 1.0
0,88 - 1
FLUID FILM Liquid A, 1 liter
One component oily liquid, solvent-free, lanolin based soft coating.
1 liter bottle
Viscosity: low (eg. like olive oil)
Creep ability: + + + + +
Protection: min. 2 years (in closed cavities)
Processing: with conventional compressed air systems without heating the material or in the flood method
General usage:
This non oxidizing rust retarding compound formulated as a liquid is
used to form protective films in ballast tanks on ships, drilling platforms,
dry docks, barges, rudder interiors, chain lockers, and any metal surface
subjected to severe salt water corrosion and to corrosive marine
atmospheres.
FLUID FILM Liquid A is easily applied by spray or floatation methods. It
forms with water or air humidity a gel which adheres to metal surfaces
and is not subject to discharge overboard during deballasting.
FLUID FILM Liquid A is also used as a penetrant and lubricant. It may
be used to help descale tanks with heavy scale.
Principal characteristics:
contains highly polar lanolin and water displacing additives, which
deposit the product below water films on the metal surfaces. This is
essential for proper penetration and adhesion of the protective coating
being applied;
does not contain solvents, non toxic during application;
requires minimum surface preparation;
penetrates existing rust, displaces water, forms with water and/or air
humidity a gel;
adheres to and gives full protection to wet or dry surfaces;
does not dry out, harden or crack;
resists water washing yet can easily be removed when required;
can be applied by air and airless spraying, brush, roller and floatation.
FLUID FILM Liquid A meets and surpasses the requirements of the
United States Military Specification MIL-C-16173.
Airless spraying equipment:
Applied by:
Amount of coats
Average film thickness in
μm
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
-
Roller
1
80
0,08
12
-
Airspray
1
170
0,17
6
0,4
Airless
1
170
0,17
6
14
Floatation
-
500 - 1500
0,5 - 1,5
2 - 0,7
-
*) The film thickness is indicated for rusted steel.
FLUID FILM Liquid A, 1 liter
One component oily liquid, solvent-free, lanolin based soft coating.
1 liter standard can
Viscosity: low (eg. like olive oil)
Creep ability: + + + + +
Protection: min. 2 years (in closed cavities)
Processing: with conventional compressed air systems without heating the material or in the flood method
General usage:
This non oxidizing rust retarding compound formulated as a liquid is
used to form protective films in ballast tanks on ships, drilling platforms,
dry docks, barges, rudder interiors, chain lockers, and any metal surface
subjected to severe salt water corrosion and to corrosive marine
atmospheres.
FLUID FILM Liquid A is easily applied by spray or floatation methods. It
forms with water or air humidity a gel which adheres to metal surfaces
and is not subject to discharge overboard during deballasting.
FLUID FILM Liquid A is also used as a penetrant and lubricant. It may
be used to help descale tanks with heavy scale.
Principal characteristics:
contains highly polar lanolin and water displacing additives, which
deposit the product below water films on the metal surfaces. This is
essential for proper penetration and adhesion of the protective coating
being applied;
does not contain solvents, non toxic during application;
requires minimum surface preparation;
penetrates existing rust, displaces water, forms with water and/or air
humidity a gel;
adheres to and gives full protection to wet or dry surfaces;
does not dry out, harden or crack;
resists water washing yet can easily be removed when required;
can be applied by air and airless spraying, brush, roller and floatation.
FLUID FILM Liquid A meets and surpasses the requirements of the
United States Military Specification MIL-C-16173.
Airless spraying equipment:
Applied by:
Amount of coats
Average film thickness in
μm
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
-
Roller
1
80
0,08
12
-
Airspray
1
170
0,17
6
0,4
Airless
1
170
0,17
6
14
Floatation
-
500 - 1500
0,5 - 1,5
2 - 0,7
-
*) The film thickness is indicated for rusted steel.
FLUID FILM Liquid A, 20 liter
One component oily liquid, solvent-free, lanolin based soft coating.
20 liter bottle
Viscosity: low (eg. like olive oil)
Creep ability: + + + + +
Protection: min. 2 years (in closed cavities)
Processing: with conventional compressed air systems without heating the material or in the flood method
General usage:
This non oxidizing rust retarding compound formulated as a liquid is
used to form protective films in ballast tanks on ships, drilling platforms,
dry docks, barges, rudder interiors, chain lockers, and any metal surface
subjected to severe salt water corrosion and to corrosive marine
atmospheres.
FLUID FILM Liquid A is easily applied by spray or floatation methods. It
forms with water or air humidity a gel which adheres to metal surfaces
and is not subject to discharge overboard during deballasting.
FLUID FILM Liquid A is also used as a penetrant and lubricant. It may
be used to help descale tanks with heavy scale.
Principal characteristics:
contains highly polar lanolin and water displacing additives, which
deposit the product below water films on the metal surfaces. This is
essential for proper penetration and adhesion of the protective coating
being applied;
does not contain solvents, non toxic during application;
requires minimum surface preparation;
penetrates existing rust, displaces water, forms with water and/or air
humidity a gel;
adheres to and gives full protection to wet or dry surfaces;
does not dry out, harden or crack;
resists water washing yet can easily be removed when required;
can be applied by air and airless spraying, brush, roller and floatation.
FLUID FILM Liquid A meets and surpasses the requirements of the
United States Military Specification MIL-C-16173.
Airless spraying equipment:
Applied by:
Amount of coats
Average film thickness in
μm
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
-
Roller
1
80
0,08
12
-
Airspray
1
170
0,17
6
0,4
Airless
1
170
0,17
6
14
Floatation
-
500 - 1500
0,5 - 1,5
2 - 0,7
-
*) The film thickness is indicated for rusted steel.
FLUID FILM Liquid A, 5 liter
One component oily liquid, solvent-free, lanolin based soft coating.
5 liter bottle
Viscosity: low (eg. like olive oil)
Creep ability: + + + + +
Protection: min. 2 years (in closed cavities)
Processing: with conventional compressed air systems without heating the material or in the flood method
General usage:
This non oxidizing rust retarding compound formulated as a liquid is
used to form protective films in ballast tanks on ships, drilling platforms,
dry docks, barges, rudder interiors, chain lockers, and any metal surface
subjected to severe salt water corrosion and to corrosive marine
atmospheres.
FLUID FILM Liquid A is easily applied by spray or floatation methods. It
forms with water or air humidity a gel which adheres to metal surfaces
and is not subject to discharge overboard during deballasting.
FLUID FILM Liquid A is also used as a penetrant and lubricant. It may
be used to help descale tanks with heavy scale.
Principal characteristics:
contains highly polar lanolin and water displacing additives, which
deposit the product below water films on the metal surfaces. This is
essential for proper penetration and adhesion of the protective coating
being applied;
does not contain solvents, non toxic during application;
requires minimum surface preparation;
penetrates existing rust, displaces water, forms with water and/or air
humidity a gel;
adheres to and gives full protection to wet or dry surfaces;
does not dry out, harden or crack;
resists water washing yet can easily be removed when required;
can be applied by air and airless spraying, brush, roller and floatation.
FLUID FILM Liquid A meets and surpasses the requirements of the
United States Military Specification MIL-C-16173.
Airless spraying equipment:
Applied by:
Amount of coats
Average film thickness in
μm
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
-
Roller
1
80
0,08
12
-
Airspray
1
170
0,17
6
0,4
Airless
1
170
0,17
6
14
Floatation
-
500 - 1500
0,5 - 1,5
2 - 0,7
-
*) The film thickness is indicated for rusted steel.
FLUID FILM Liquid AR 1 liter
FLUID FILM Liquid AR is a transparent, solvent-free physiologically harmless soft single-layer corrosion protection coating based on lanolin.
1 liter
Viscosity: medium (e.g. like honey)
Creep ability: + + +
Protection time: approx. 15 years (in closed cavities)
Features
Solvent-free and physiologically harmless during processing, greater safety in operation.
Economical to use and uncomplicated to apply.
A layer thickness of between 200 - 800 μm can be applied in one operation (by airless spraying).
Can be sprayed with commercially available airless equipment (compressing over 22:1). Application is possible by brush, rollers or compressed air spraying (with pressure barrel).
Simplified method of application when spraying by means of lances, which in the majority of cases makes the erection of a scaffold unnecessary.
1-component product with excellent adhesion even on damp surfaces and old coatings.
Excellent penetration of thick rust layers - intensive surface preparation is not necessary (penetrated rust layers can be removed from the substrate).
rust layers may fall off from the substrate after some time).
If FLUID FILM Liquid AR has been used as a rust remover, regular repair work or renewal coatings can be carried out immediately with FLUID FILM products only after all loose dirt has been removed.
Mode of operation:
FLUID FILM Liquid AR is a thixotropic product that reduces viscosity by stirring. viscosity by stirring and facilitates transfer or filling into other containers. into other containers. We recommend the use of mechanical stirring equipment.
The processing temperature for FLUID FILM Liquid AR is between -15°C (263 K) and 40°C (313 K). In order to achieve the required pressure of 150 bar at the nozzle at low temperatures, we recommend preheating. we recommend preheating the material to approx. 25°C.
During application, the film thickness must be continuously checked to avoid under- or overcoating.
or overcoating must be checked continuously. When using the airless spraying method, areas which are difficult to access can be coated by means of lances. be coated by means of lances.
The pneumatic spraying technique can only be used if the material is transported to the nozzle under pressure, i.e. when using of pressure vessels or combination units.
Application data:
Applied by:
Amount of coats
Average film thickness in μm
Theoretical consumpton in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
50
0,05
20
-
Roller
1
50
0,05
20
-
Airspray
1
200
0,2
5
1,5 - 0,4
Airless
1
400-800
0,4 - 0,8
2,5 - 1,25
0,63 - 14
FLUID FILM Liquid AR 20 liter
FLUID FILM Liquid AR is a transparent, solvent-free physiologically harmless soft single-layer corrosion protection coating based on lanolin.
20 liter
Viscosity: medium (e.g. like honey)
Creep ability: + + +
Protection time: approx. 15 years (in closed cavities)
Features
Solvent-free and physiologically harmless during processing, greater safety in operation.
Economical to use and uncomplicated to apply.
A layer thickness of between 200 - 800 μm can be applied in one operation (by airless spraying).
Can be sprayed with commercially available airless equipment (compressing over 22:1). Application is possible by brush, rollers or compressed air spraying (with pressure barrel). (see 9.)
Simplified method of application when spraying by means of lances, which in the majority of cases makes the erection of a scaffold unnecessary.
1-component product with excellent adhesion even on damp surfaces and old coatings.
Excellent penetration of thick rust layers - intensive surface preparation is not necessary (penetrated rust layers can be removed from the substrate).
rust layers may fall off from the substrate after some time).
If FLUID FILM Liquid AR has been used as a rust remover, regular repair work or renewal coatings can be carried out immediately with FLUID FILM products only after all loose dirt has been removed.
Mode of operation:
FLUID FILM Liquid AR is a thixotropic product that reduces viscosity by stirring.
viscosity by stirring and facilitates transfer or filling into other containers.
into other containers. We recommend the use of mechanical
stirring equipment.
The processing temperature for FLUID FILM Liquid AR is between
-15°C (263 K) and 40°C (313 K). In order to achieve the required
pressure of 150 bar at the nozzle at low temperatures, we recommend preheating.
we recommend preheating the material to approx. 25°C.
During application, the film thickness must be continuously checked to avoid under- or overcoating.
or overcoating must be checked continuously.
d.When using the airless spraying method, areas which are difficult to access can be coated by means of lances.
be coated by means of lances.
The pneumatic spraying technique can only be used if
the material is transported to the nozzle under pressure, i.e. when using
of pressure vessels or combination units.
Application data:
Applied by:
Amount of coats
Average film thickness in μm
Theoretical consumpton in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
50
0,05
20
-
Roller
1
50
0,05
20
-
Airspray
1
200
0,2
5
1,5 - 0,4
Airless
1
400-800
0,4 - 0,8
2,5 - 1,25
0,63 - 14
FLUID FILM Liquid AR 5 liter
FLUID FILM Liquid AR is a transparent, solvent-free physiologically harmless soft single-layer corrosion protection coating based on lanolin.
5 liter
Viscosity: medium (e.g. like honey)
Creep ability: + + +
Protection time: approx. 15 years (in closed cavities)
Features
Solvent-free and physiologically harmless during processing, greater safety in operation.
Economical to use and uncomplicated to apply.
A layer thickness of between 200 - 800 μm can be applied in one operation (by airless spraying).
Can be sprayed with commercially available airless equipment (compressing over 22:1). Application is possible by brush, rollers or compressed air spraying (with pressure barrel). (see 9.)
Simplified method of application when spraying by means of lances, which in the majority of cases makes the erection of a scaffold unnecessary.
1-component product with excellent adhesion even on damp surfaces and old coatings.
Excellent penetration of thick rust layers - intensive surface preparation is not necessary (penetrated rust layers can be removed from the substrate).
rust layers may fall off from the substrate after some time).
If FLUID FILM Liquid AR has been used as a rust remover, regular repair work or renewal coatings can be carried out immediately with FLUID FILM products only after all loose dirt has been removed.
Mode of operation:
FLUID FILM Liquid AR is a thixotropic product that reduces viscosity by stirring.
viscosity by stirring and facilitates transfer or filling into other containers.
into other containers. We recommend the use of mechanical
stirring equipment.
The processing temperature for FLUID FILM Liquid AR is between
-15°C (263 K) and 40°C (313 K). In order to achieve the required
pressure of 150 bar at the nozzle at low temperatures, we recommend preheating.
we recommend preheating the material to approx. 25°C.
During application, the film thickness must be continuously checked to avoid under- or overcoating.
or overcoating must be checked continuously.
d.When using the airless spraying method, areas which are difficult to access can be coated by means of lances.
be coated by means of lances.
The pneumatic spraying technique can only be used if
the material is transported to the nozzle under pressure, i.e. when using
of pressure vessels or combination units.
Application data:
Applied by:
Amount of coats
Average film thickness in μm
Theoretical consumpton in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
50
0,05
20
-
Roller
1
50
0,05
20
-
Airspray
1
200
0,2
5
1,5 - 0,4
Airless
1
400-800
0,4 - 0,8
2,5 - 1,25
0,63 - 14
FLUID FILM LIQUID NAS 1 liter
FLUID FILM NAS is mainly intended for protection of metal surfaces during internal temporary storage and for preservation during sea and road transport and for cavity sealing of motor vehicles.
1 liter
Viscosity: low (e.g. like ketchup)
Creep ability: + + + +
Protection time: approx. 6 years (in closed cavities)
Processing: with commercially available compressed air systems after heating the material to approx. 25°C or with airless systems
Features
Solvent-free and physiologically safe for application and as a protective film.
Requires minimal surface treatment.
Penetrates through rust, displaces water and forms an extremely resistant protection against corrosion by salts.
Good adhesion to wet or dry surfaces.
No evaporation, resinification or drying of the protective film.
Can be easily removed if necessary.
Can come into contact with water immediately after application.
Processing after slight warming to approx. 25 °C, also possible with a standard pressure cup gun.
Particularly suitable as a lubricant and penetrating oil.
Application:
Surface preparation:
FLUID FILM NAS can be used as a rust remover and at the same time as a corrosion inhibitor.
For economic reasons, it is recommended to remove loose contamination such as rust and old coating parts by washing.
The surface may be damp, but must be freed from surface water.
Mode of operation:
For temporary corrosion protection during transport by sea and for intermediate storage under roof.
By brush or roller by one-time application,
or by spraying with the help of compressed air systems
For the preservation of cavities and inaccessible places
With a pressure cup gun and a cavity probe, after heating to approx. 25 °C while stirring
Airless spraying equipment:
Applied by:
Amount of coats
Average film thickness in μm *)
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
-
Roller
1
80
0,08
12
-
Airspray
1
170
0,17
6
0,8 - 0,4
Airless
1
170
0,17
6
0,63 - 14
Effect:
Extremely resistant to all weather conditions, including snow and slush and the solvent salts used in winter maintenance.
Extremely effective and reliable at the same time as a rust remover and water-displacing corrosion inhibitor.
Excellent salt water resistance.
As corrosion protection of steel parts and other metal parts during transport and processing in the manufacturing plant.
Fast creeping, yet well adhering, temperature stable, will not be washed off or altered by rain or seawater, nor will it evaporate and gum up as most penetrating oils do.
Bitumen protection layers already on the car chassis floors are plasticized by FLUID FILM and thus activated.
FLUID FILM LIQUID NAS 1 liter standard can
FLUID FILM NAS is mainly intended for protection of metal surfaces during internal temporary storage and for preservation during sea and road transport and for cavity sealing of motor vehicles.
1 liter standard can
Viscosity: low (e.g. like ketchup)
Creep ability: + + + +
Protection time: approx. 6 years (in closed cavities)
Processing: with commercially available compressed air systems after heating the material to approx. 25°C or with airless systems
Features
Solvent-free and physiologically safe for application and as a protective film.
Requires minimal surface treatment.
Penetrates through rust, displaces water and forms an extremely resistant protection against corrosion by salts.
Good adhesion to wet or dry surfaces.
No evaporation, resinification or drying of the protective film.
Can be easily removed if necessary.
Can come into contact with water immediately after application.
Processing after slight warming to approx. 25 °C, also possible with a standard pressure cup gun.
Particularly suitable as a lubricant and penetrating oil.
Application:
Surface preparation:
FLUID FILM NAS can be used as a rust remover and at the same time as a corrosion inhibitor.
For economic reasons, it is recommended to remove loose contamination such as rust and old coating parts by washing.
The surface may be damp, but must be freed from surface water.
Mode of operation:
For temporary corrosion protection during transport by sea and for intermediate storage under roof.
By brush or roller by one-time application,
or by spraying with the help of compressed air systems
For the preservation of cavities and inaccessible places
With a pressure cup gun and a cavity probe, after heating to approx. 25 °C while stirring
Airless spraying equipment:
Applied by:
Amount of coats
Average film thickness in μm *)
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
-
Roller
1
80
0,08
12
-
Airspray
1
170
0,17
6
0,8 - 0,4
Airless
1
170
0,17
6
0,63 - 14
Effect:
Extremely resistant to all weather conditions, including snow and slush and the solvent salts used in winter maintenance.
Extremely effective and reliable at the same time as a rust remover and water-displacing corrosion inhibitor.
Excellent salt water resistance.
As corrosion protection of steel parts and other metal parts during transport and processing in the manufacturing plant.
Fast creeping, yet well adhering, temperature stable, will not be washed off or altered by rain or seawater, nor will it evaporate and gum up as most penetrating oils do.
Bitumen protection layers already on the car chassis floors are plasticized by FLUID FILM and thus activated.
FLUID FILM LIQUID NAS 20 liter
FLUID FILM NAS is mainly intended for protection of metal surfaces during internal temporary storage and for preservation during sea and road transport and for cavity sealing of motor vehicles.
20 liter
Viscosity: low (e.g. like ketchup)
Creep ability: + + + +
Protection time: approx. 6 years (in closed cavities)
Processing: with commercially available compressed air systems after heating the material to approx. 25°C or with airless systems
Features
Solvent-free and physiologically safe for application and as a protective film.
Requires minimal surface treatment.
Penetrates through rust, displaces water and forms an extremely resistant protection against corrosion by salts.
Good adhesion to wet or dry surfaces.
No evaporation, resinification or drying of the protective film.
Can be easily removed if necessary.
Can come into contact with water immediately after application.
Processing after slight warming to approx. 25 °C, also possible with a standard pressure cup gun.
Particularly suitable as a lubricant and penetrating oil.
Application:
Surface preparation:
FLUID FILM NAS can be used as a rust remover and at the same time as a corrosion inhibitor.
For economic reasons, it is recommended to remove loose contamination such as rust and old coating parts by washing.
The surface may be damp, but must be freed from surface water.
Mode of operation:
For temporary corrosion protection during transport by sea and for intermediate storage under roof.
By brush or roller by one-time application,
or by spraying with the help of compressed air systems
For the preservation of cavities and inaccessible places
With a pressure cup gun and a cavity probe, after heating to approx. 25 °C while stirring
Airless spraying equipment:
Applied by:
Amount of coats
Average film thickness in μm *)
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
-
Roller
1
80
0,08
12
-
Airspray
1
170
0,17
6
0,8 - 0,4
Airless
1
170
0,17
6
0,63 - 14
Effect:
Extremely resistant to all weather conditions, including snow and slush and the solvent salts used in winter maintenance.
Extremely effective and reliable at the same time as a rust remover and water-displacing corrosion inhibitor.
Excellent salt water resistance.
As corrosion protection of steel parts and other metal parts during transport and processing in the manufacturing plant.
Fast creeping, yet well adhering, temperature stable, will not be washed off or altered by rain or seawater, nor will it evaporate and gum up as most penetrating oils do.
Bitumen protection layers already on the car chassis floors are plasticized by FLUID FILM and thus activated.
FLUID FILM LIQUID NAS 5 liter
FLUID FILM NAS is mainly intended for protection of metal surfaces during internal temporary storage and for preservation during sea and road transport and for cavity sealing of motor vehicles.
5 liter
Viscosity: low (e.g. like ketchup)
Creep ability: + + + +
Protection time: approx. 6 years (in closed cavities)
Processing: with commercially available compressed air systems after heating the material to approx. 25°C or with airless systems
Features
Solvent-free and physiologically safe for application and as a protective film.
Requires minimal surface treatment.
Penetrates through rust, displaces water and forms an extremely resistant protection against corrosion by salts.
Good adhesion to wet or dry surfaces.
No evaporation, resinification or drying of the protective film.
Can be easily removed if necessary.
Can come into contact with water immediately after application.
Processing after slight warming to approx. 25 °C, also possible with a standard pressure cup gun.
Particularly suitable as a lubricant and penetrating oil.
Application:
Surface preparation:
FLUID FILM NAS can be used as a rust remover and at the same time as a corrosion inhibitor.
For economic reasons, it is recommended to remove loose contamination such as rust and old coating parts by washing.
The surface may be damp, but must be freed from surface water.
Mode of operation:
For temporary corrosion protection during transport by sea and for intermediate storage under roof.
By brush or roller by one-time application,
or by spraying with the help of compressed air systems
For the preservation of cavities and inaccessible places
With a pressure cup gun and a cavity probe, after heating to approx. 25 °C while stirring
Airless spraying equipment:
Applied by:
Amount of coats
Average film thickness in μm *)
Theoretical consumption in l/m²
Theoretical spreading rate in m²/l
Nozzle
Brush
1
80
0,08
12
-
Roller
1
80
0,08
12
-
Airspray
1
170
0,17
6
0,8 - 0,4
Airless
1
170
0,17
6
0,63 - 14
Effect:
Extremely resistant to all weather conditions, including snow and slush and the solvent salts used in winter maintenance.
Extremely effective and reliable at the same time as a rust remover and water-displacing corrosion inhibitor.
Excellent salt water resistance.
As corrosion protection of steel parts and other metal parts during transport and processing in the manufacturing plant.
Fast creeping, yet well adhering, temperature stable, will not be washed off or altered by rain or seawater, nor will it evaporate and gum up as most penetrating oils do.
Bitumen protection layers already on the car chassis floors are plasticized by FLUID FILM and thus activated.
MULTI FILM 1 liter BLACK
MULTI FILM from Hodt Fluid Film protects and preserves as a compact coating material as well as a primer and top coat.
1 liter black
Compact coating material
Protects and preserves
Solves many rust protection problems
Features
HODT MULTI FILM is an aqueous emulsion with mild odor, low VOC content and very low toxicity.
It is a non-hazardous and environmentally friendly alternative to solventborne topcoats and corrosion inhibitors at a dry film thickness (dft) > 100 μm.
1-component product with excellent adhesion and elasticity, rapid oxidative drying, water resistance and recoatability.
Suitable substrates: organic coatings, grease-free iron, galvanized steel, aluminum, cement plaster, plastic plaster, concrete, plastic, emulsion paint coatings, etc.
Economical to use and uncomplicated to apply. In one operation, a layer thickness of
50 to 80 μm can be applied (by spraying and dipping).
Can be diluted with water as desired, which results in a much greater reduction in viscosity
than in the case of synthetic resins with organic solvents; the product meets the highest requirements in terms of chemical
and mechanical resistance. It adheres to natural and synthetic rubber, polyethylene, PVC.
The water-based clear coat also meets the strict environmental requirements.
High elasticity of the coating ensures that no cracking or chipping occurs during expansion or contraction of the substrate.
contraction of the substrate metal.
As an oxidatively drying coating, HODT MULTI FILM must, as with alkyd products, absorb oxygen for curing.
for curing. It is therefore not sufficient for the water in the emulsion to evaporate and form a film (so-called anti-drying),
additional drying time must be allowed for the absorption of oxygen in order to obtain a fully loadable coating.
coating is obtained.
Although HODT MULTI FILM is highly resistant to solvents, i.e. it can be used as a primer for other coatings, it is advisable to use it as a primer for other coatings.
it is advisable to perform a resistance test on a small area before such an application.
Mode of operation:
The substrate for HODT MULTI FILM must be free of grease!
When applying HODT MULTI FILM by brush, roller, dipping or spraying, always apply "dry on dry" (after approx. 2 hours) to obtain a film thickness of approx. 120 - 160 μm.
For spraying, HODT MULTI FILM can be diluted with water if necessary.
However, after dilution, more coats must be applied to create the desired optimum film thickness.
This drying time depends on the temperature. Forced drying at a temperature of 50 - 60 °C can reduce the drying time to 2 -3 hours.
On the other hand, at a normal temperature of approx. 20°C, a drying time of 24 hours must be expected before further coats of HODT MULTI FILM or other paints can be applied to the multifilm coating.
Technical Merkmale:
Temperature range (in °C): -40°C to 120°C (+150° short).
Touch dry: (at 20 °C u. 25 μm film thickness): 2 hrs.
Curing time (at 20 °C in hours): 24
Solvent resistance: good
Moisture resistance: good
Thinner: water
also available in aerosol: no
Color: black
Dynamic viscosity: (10 1/s; 23 °C) DIN EN ISO 3219 10000 mPa.sek
Flash point (in liquid form): not applicable
Solids content (wt%): 34-36
Spec. weight: 1.02 g/cm³
Salt spray test according to DIN EN ISO 9227 Duration 480 h
Gasfüllung Acetylen 5 Liter/0,8 kg
An unserem Standort in Aachen liefern wir technische Gase im Tauschverfahren, leer gegen voll.
Die hier angebotenen Flaschen sind regenerierte, d.h. überholte Flaschen mit TÜV-Abnahme. Rechtlich sind es also gebrauchte Flaschen, was für die Nutzung natürlich keine Rolle spielt.
Als Eigentumsflasche können Sie die Flaschen bei jedem Abfüller füllen lassen.
Mit Eigentumsflaschen ist das Thema Flaschenmiete für Sie erledigt.
ACHTUNG: Gasfüllungen werden nicht versandt, das Angebot richtet sich ausschließlich an Abholer !
Technische Daten:
Chemische Formel: C2H2
Füllvolumen: 5 Liter
Füllgewicht: 0,8 kg
Flaschendurchmesser ca: 140 mm*
Flaschenhöhe ca: 600 mm*
Taragewicht (leer) ca: 8 kg*
(*Aufgrund der vielfältigen Bauformen sind die Gewichts- & Maßangaben unverbindlich)
Gasfüllungen
Bei nicht bei uns gekauften Flaschen wird einmalig ein Fremdflaschenzuschlag in Höhe von EUR 20,- berechnet.
Voraussetzung ist, dass die angelieferte Flasche eine Eigentumsflasche ist. Mietflaschen können von uns nicht getauscht werden.
Nicht bei uns gekaufte Flaschen müssen noch mindestens drei Jahre TÜV-frei sein, andernfalls wird zusätzlich eine anteilige Prüfgebühr in Höhe von EUR 60,- berechnet.
Gasfüllung Acetylen 10 Liter/1,6 kg
An unserem Standort in Aachen liefern wir technische Gase im Tauschverfahren, leer gegen voll.
Die hier angebotenen Flaschen sind regenerierte, d.h. überholte Flaschen mit TÜV-Abnahme. Rechtlich sind es also gebrauchte Flaschen, was für die Nutzung natürlich keine Rolle spielt.
Als Eigentumsflasche können Sie die Flaschen bei jedem Abfüller füllen lassen.
Mit Eigentumsflaschen ist das Thema Flaschenmiete für Sie erledigt.
ACHTUNG: Gasfüllungen werden nicht versandt, das Angebot richtet sich ausschließlich an Abholer !
Technische Daten:
Chemische Formel: C2H2
Füllvolumen: 10 Liter
Füllgewicht: 1,6 kg
Flaschendurchmesser ca: 140 mm*
Flaschenhöhe ca: 970 mm*
Taragewicht (leer) ca: 20 kg*
(*Aufgrund der vielfältigen Bauformen sind die Gewichts- & Maßangaben unverbindlich)
Gasfüllungen
Bei nicht bei uns gekauften Flaschen wird einmalig ein Fremdflaschenzuschlag in Höhe von EUR 20,- berechnet.
Voraussetzung ist, dass die angelieferte Flasche eine Eigentumsflasche ist. Mietflaschen können von uns nicht getauscht werden.
Nicht bei uns gekaufte Flaschen müssen noch mindestens drei Jahre TÜV-frei sein, andernfalls wird zusätzlich eine anteilige Prüfgebühr in Höhe von EUR 60,- berechnet.
Gasfüllung Acetylen 20 Liter/3,2 kg
An unserem Standort in Aachen liefern wir technische Gase im Tauschverfahren, leer gegen voll.
Die hier angebotenen Flaschen sind regenerierte, d.h. überholte Flaschen mit TÜV-Abnahme. Rechtlich sind es also gebrauchte Flaschen, was für die Nutzung natürlich keine Rolle spielt.
Als Eigentumsflasche können Sie die Flaschen bei jedem Abfüller füllen lassen.
Mit Eigentumsflaschen ist das Thema Flaschenmiete für Sie erledigt.
ACHTUNG: Gasfüllungen werden nicht versandt, das Angebot richtet sich ausschließlich an Abholer !
Technische Daten:
Chemische Formel: C2H2
Füllvolumen: 20 Liter
Füllgewicht: 3,2 kg
Flaschendurchmesser ca: 200 mm*
Flaschenhöhe ca: 950 mm*
Taragewicht (leer) ca: 36 kg*
(*Aufgrund der vielfältigen Bauformen sind die Gewichts- & Maßangaben unverbindlich)
Gasfüllungen
Bei nicht bei uns gekauften Flaschen wird einmalig ein Fremdflaschenzuschlag in Höhe von EUR 20,- berechnet.
Voraussetzung ist, dass die angelieferte Flasche eine Eigentumsflasche ist. Mietflaschen können von uns nicht getauscht werden.
Nicht bei uns gekaufte Flaschen müssen noch mindestens drei Jahre TÜV-frei sein, andernfalls wird zusätzlich eine anteilige Prüfgebühr in Höhe von EUR 60,- berechnet.
Gasfüllung Acetylen 48 Liter/8 kg
An unserem Standort in Aachen liefern wir technische Gase im Tauschverfahren, leer gegen voll.
Die hier angebotenen Flaschen sind regenerierte, d.h. überholte Flaschen mit TÜV-Abnahme. Rechtlich sind es also gebrauchte Flaschen, was für die Nutzung natürlich keine Rolle spielt.
Als Eigentumsflasche können Sie die Flaschen bei jedem Abfüller füllen lassen.
Mit Eigentumsflaschen ist das Thema Flaschenmiete für Sie erledigt.
ACHTUNG: Gasfüllungen werden nicht versandt, das Angebot richtet sich ausschließlich an Abholer !
Technische Daten:
Chemische Formel: C2H2
Füllvolumen: 48 Liter
Füllgewicht: 8 kg
Flaschendurchmesser ca: 200 mm*
Flaschenhöhe ca: 1650 mm*
Taragewicht (leer) ca: 65 kg*
(*Aufgrund der vielfältigen Bauformen sind die Gewichts- & Maßangaben unverbindlich)
Gasfüllungen
Bei nicht bei uns gekauften Flaschen wird einmalig ein Fremdflaschenzuschlag in Höhe von EUR 20,- berechnet.
Voraussetzung ist, dass die angelieferte Flasche eine Eigentumsflasche ist. Mietflaschen können von uns nicht getauscht werden.
Nicht bei uns gekaufte Flaschen müssen noch mindestens drei Jahre TÜV-frei sein, andernfalls wird zusätzlich eine anteilige Prüfgebühr in Höhe von EUR 60,- berechnet.
